Electrical & Controls Systems Engineer

Electrical & Controls Systems Engineer

We are looking for a Lead Electrical & Controls Systems Engineer who takes personal responsibility for every connection, from incoming power to the last sensor signal. We want a builder who designs the panel, writes the logic, works alongside the assembly team, and troubleshoots the physical system. You will lead through technical judgment, hands-on execution, and ownership of the finished product.

The Role

You will own our electrical and controls stack A Z. This is a role at the intersection of Industrial Automation, Power Distribution, and Product Engineering. You will set the technical direction and stay close to implementation. You will be:

• Designing electrical and controls architecture for modular skids and containerized treatment systems.
• Developing control panels, electrical drawings, PLC programs, and system interconnections.
• Working with suppliers and our engineering team to turn designs into clean, repeatable products.
• Establishing standards that make systems easier to build, test, commission, and service.

What You Will Build

The Power Architecture

Design power distribution for 480V, 120/208V, and 24VDC systems. Specify protection, grounding, isolation, and interfaces for pumps, drives, instruments, and control equipment.

The Control Panel

Own panel layouts, schematics, wiring diagrams, I/O schedules, and electrical BOMs. Work with suppliers to select and validate components that are reliable, available, cost-effective, and practical to assemble.

The Automation Stack

Develop PLC logic, HMI interfaces, operating sequences, alarms, and interlocks. Translate process requirements into controls that handle normal operation, startup, shutdown, and fault recovery.

The Connected Product

Engineer power and controls connections between skids and containers. Own cable selection, connectors, routing, segregation, labeling, and industrial networking so the delivered system is organized, robust, and serviceable.

The DNA We Are Looking For

Experimentalist First

You wire, program, power up, and test. You can explain systems you personally built, the problems you encountered, and how you resolved them.

First-Principles Thinker

You understand why a drive trips, a signal becomes noisy, or a network loses communication. You form a hypothesis, measure what matters, and verify the fix.

Extreme Ownership

You take responsibility for the complete stack. You follow problems across hardware, software, suppliers, and installation until the system performs reliably.

Cross-Disciplinary Leader

You translate process intent into electrical and automation decisions. You work closely with mechanical engineers, process engineers, fabricators, and operators, and raise the quality of the team's work through clear standards and practical guidance.

Critical Requirements

Electrical & Panel Design

Practical experience with 480V, 120/208V, and 24VDC systems, including control panel design, electrical drawings, component sizing, circuit protection, grounding, and safe troubleshooting.

PLC & Automation

Hands-on PLC programming experience and the ability to develop structured, maintainable control logic. Siemens experience is preferred; experience with Beckhoff or comparable industrial platforms is valuable.

Industrial Communications

Familiarity with OPC UA, PROFINET, and EtherNet/IP, including device integration, network configuration, and communication troubleshooting.

System Integration & Wiring

Experience designing power and controls interconnections across equipment assemblies. You understand cable routing, power and signal segregation, termination, labeling, and access for assembly and maintenance.

Technical & Supplier Ownership

Demonstrated ability to independently own electrical and controls design, guide implementation, and work directly with suppliers on component selection and substitutions. You can make sound tradeoffs across performance, safety, cost, and lead time.

Nice to Haves

• Experience delivering systems from project development and design through commissioning and performance validation.
• Familiarity with IO-Link devices and integration.
• Experience interfacing with customers during requirements definition, site installation, troubleshooting, or operator training.
• Experience with modular water treatment equipment or similar industrial process systems.

About MY HR:
MY HR is an award-winning, woman and minority-owned firm based in Atlanta. We specialize in providing full-service professional HR services, and are proud to be an equal opportunity employer. With a commitment to excellence and a focus on diversity, we strive to help businesses of all sizes achieve their human resources goals.

Follow us for more info:

linkedin.com/company/my-hr/
facebook.com/myhrsupplier
instagram.com/myhrmanagement/

MY HR is an award-winning Full-Service Professional Human Resources Consulting firm offering Staff Augmentation, Project and SOW staffing, Permanent Placement, Recruitment Process Outsourcing (RPO), Payroll Services, and full range HR Services including compliance, training, and workforce development. With our personal touch, we help small to mid-sized companies as well as Fortune 500 companies grow and strengthen in the HR area by providing customized HR solutions.

Check out our website: myhrmgmt.com