Testing Technician

Testing TechnicianEaton's ES AMER ARS division is currently seeking a Testing Technician to join our Fibrebond team in Minden, LA!You will work an average of 54 hours per week (including OT) from 6 am - 4:30 pm, M-F. There is overtime every other Saturday from 6 am - 2:30 pm. The hourly rate for this position is $16.50 per hour. Please note the salary information shown above is a general guideline only. Salaries are based upon candidate skills, experience, and qualifications, as well as market and business considerations.What You'll Do:The Testing Technician is responsible for inspecting & testing production processes and completed work to ensure products meet engineering, company, and customer specifications. This role verifies shelter builds against engineering drawings and Quality Travelers, documents discrepancies, and works cross-functionally to ensure corrective actions are completed. The Testing Technician may support inspections & testing across multiple production areas and assist with training and coaching team members on quality & testing expectations. In this function you will:Inspect & test production processes and finished units for compliance with engineering drawings, customer specifications, and Quality TravelersSupport commissioning for HVAC HMI/PLC programming, Li-ion Tamer testing, fire control operation, HVAC startup/troubleshooting, and loadbank KW set point controlSupport energized testing, including breaker operation with arc flash PPE, MCC/switchgear/VFD power-up, Prime PLC communication, UPS testing states, and OEM troubleshooting coordinationCoordinate testing team activities, safety meetings, JHA/MOP completion, inspection communication, training, commissioning support, and reinforcement of quality, workmanship, and SOP expectationsPerform inspections and audits to Quality Travelers, drawings, SOPs, L2 checklists, NEC requirements, and equipment documents; verify hold points, signoffs, acceptance criteria, hardware, buss bars, conduit fill, and documentation accuracyInspect and test electrical integration work for torque, grounding, terminations, labeling, insulation, phase/voltage checks, High Pot/Meggar testing, wireway/cable tray installation, and grounding continuityIdentify, document, contain, communicate, and escalate nonconformances; initiate hold or stop-work actions for safety, compliance, customer, or workmanship risksProcess nonconforming material through DMR, including identification, tagging, segregation, review, disposition, resolution, and corrective action support using 8D, 5-Why, or A3 methodsRecord inspection and test results in Quality Travelers and daily reports to support NCR reporting, KPIs, trend analysis, QMS compliance, and audit readinessSupport incoming, supplier, warranty, and field quality issues through inspection, documentation, escalation, investigation, and cross-functional communicationProvide inspection support across multiple production areas as neededFollow all safety procedures, wear required PPE, and maintain a clean, organized work areaPerform other duties as assigned by managerQualifications:Required (Basic) Qualifications• High school diploma or GED from an accredited institution• No relocation benefit is offered for this position. Only candidates residing within the immediate area of the Minden, LA facility (50-mile radius) will be considered for this position. Active Duty Military Service member candidates are exempt from the geographical area limitation• Eaton will not consider applicants for employment immigration sponsorship or support for this position. This means that Eaton will not support any CPT, OPT, or STEM OPT plans, F-1 to H-1B cap registration, O-1, E-3, TN status, I-485 job portability, etc.Preferred Qualifications• Experience reading and interpreting engineering drawings, customer specifications, bills of material, and applicable industrial trade standards• Experience using inspection, measurement, hand, power, and electrical troubleshooting tools, including tape measures, torque tools, gauges, and Fluke multimetersSkills/Position Criteria:• Ability to read and interpret engineering drawings, customer specifications, bills of material, and applicable industrial trade standards• Ability to use inspection, measurement, hand, power, and electrical troubleshooting tools, including tape measures, torque tools, gauges, and Fluke multimeters• Ability to work safely and effectively in a team-based manufacturing environment• Ability to work overtime as required• Ability to lift, carry, push, or pull up to 50 lbs., with or without reasonable accommodation• Ability to bend, twist, reach, stand, walk, and climb ladders for elevated inspections and repairs with or without reasonable accommodation. • Ability to work outdoors in all weather conditions and seasonal temperatures• Strong communication skills, attention to detail, and ability to maintain confidentiality• Required use of personal protective equipment (PPE), including safety eyewear and steel-toed boots