Instrumentation & Controls Technician (ICT)

Job Title: Instrumentation & Controls Technician (ICT) Level I, II, II Div./Depart.: Industrial Automation Group / Operations Reports To: Vice President of Operations (VPO) Position Overview The Instrumentation & Controls Technician (ICT) is a hands-on technical professional responsible for the field commissioning, startup, and ongoing troubleshooting of SCADA control systems deployed at water and wastewater treatment facilities. Working within a project-based environment, this individual partners closely with project managers, electrical subcontractors, and client operations staff to bring new systems online and resolve issues on existing infrastructure. The role demands deep practical knowledge of industrial instrumentation, PLC-based control systems IO, and communication protocols common to water utility environments. Key Duties & Responsibilities Lead on-site commissioning of new SCADA and control system installations at water and wastewater treatment plants, pump stations, and lift stations. Perform loop checks, I/O verification, signal calibration, and functional acceptance testing prior to client handoff. Configure and test field instrumentation. Including: flow meters, pressure transmitters, level sensors, analyzers, and VFDs and relay control systems. Coordinate startup activities with IAG Engineers, electrical contractors, client operations staff, and project management to meet project milestones. Document commissioning results, as-built redlines, and startup punch lists; support closeout package preparation. Diagnose and resolve control system faults, communication failures, and instrumentation anomalies on both newly installed and legacy systems. Respond to field service calls at client facilities to assess and correct operational issues impacting operations or SCADA visibility. Troubleshoot PLCs (Allen-Bradley, Siemens, Modicon, SCADApack or equivalent), HMI platforms, RTUs, and associated field wiring. Identify root causes of recurring failures and recommend corrective actions or system improvements to engineering staff. Available for support 24/7 emergency response rotations as required by project commitments or client service agreements. With additional compensation. Documentation & Reporting Maintain accurate field notes and produce clear, structured reports on commissioning progress, service activities, and findings. Review and mark-up P&IDs, electrical schematics, panel drawings, and instrument datasheets. Submit daily field reports and time logs; flag scope changes or unforeseen conditions to the project manager promptly. Client & Site Coordination Serve as the primary technical point of contact on-site during commissioning and startup phases. Communicate effectively with plant operators and engineering staff to coordinate outages, system transfers, and preventive maintenance activities. Represent the company professionally in all client interactions; support repeat business through responsive, quality-focused service. Requirements 5–10 years of hands-on experience in instrumentation and controls within the water, wastewater, or related municipal utility sector. Demonstrated experience commissioning PLC-based control systems and SCADA platforms in industrial or utility environments. Proficiency with at least one major PLC platform (Allen-Bradley, Siemens S7, or equivalent). Working knowledge of SCADA software platforms (e.g., Ignition, Wonderware, FactoryTalk, or similar). Familiarity with industrial communication protocols: Modbus TCP/RTU, DNP3, Ethernet/IP, Profibus. Ability to read and interpret P&IDs, one-line diagrams, instrument loop drawings, and control panel schematics. Valid driver's license and ability to travel to project sites regionally. Ability to work in a field environment including confined space entry (with training), outdoor conditions, and active treatment facilities. Ability to pass DoD background checks and drug screening. Valid California driver’s license with clean driving and criminal record. Preferred ISA Certified Control Systems Technician (CCST) Level II or III, or equivalent professional certification. CWEA Electrical & Instrumentation Technology (EIT) Experience with radio telemetry systems (licensed or unlicensed spread spectrum) and cellular RTU communications.Familiarity with cybersecurity practices in OT/ICS environments (NERC CIP awareness, network segmentation concepts). Prior experience at a systems integrator or automation contractor (as opposed to owner/operator only). OSHA 10 or OSHA 30 General Industry certification. Technical Skills Summary Control Systems Instrumentation Communications & Networks HMI / SCADA Platforms 1 phase and 3 phase Flow Meters & Transmitters VFD Configuration Automated Control Valves Modbus TCP/RTU DNP3 Ethernet/IP

WORK ENVIRONMENT & PHYSICAL REQUIREMENTS

Frequent travel to client facilities including water treatment plants, pump stations, and wastewater treatment facilities. Work performed both in the field (outdoor/plant environment) and at a desk for documentation and remote support activities. Must be able to lift up to 50 lbs, work from ladders and elevated platforms, and operate in confined space environments with appropriate training and PPE. Exposure to industrial process environments; adherence to site-specific safety protocols is mandatory. ATSI’s primarily performs system integration services in the following industries: Water/Wastewater This role supports automation solutions in water treatment, distribution, and wastewater facilities. Familiarity with municipal infrastructure, SCADA telemetry systems, pump control, and regulatory reporting are essential. Technicians must understand EPA compliance standards and work frequently with city agencies, utility operators, and contractors. Food & Beverage This role supports automation systems in food and beverage processing plants. Emphasis is placed on sanitary design, CIP/SIP operations, batch processing, traceability, and integration with MES/ERP systems. Knowledge of FDA, USDA, and FSMA regulations is highly desirable, along with experience in maintaining production continuity and system validation practices. We are required by law to provide equal employment opportunity to qualified people with disabilities. We are also required to measure our progress toward having at least 7% of our workforce be individuals with disabilities. To do this, we must ask applicants and employees if they have a disability or have ever had a disability. Because a person may become disabled at any time, we ask all of our employees to update their information at least every five years. Identifying yourself as an individual with a disability is voluntary, and we hope that you will choose to do so. Your answer will be maintained confidentially and not be seen by selecting officials or anyone else involved in making personnel decisions. Completing the form will not negatively impact you in any way, regardless of whether you have self-identified in the past. For more information about this form or the equal employment obligations of federal contractors under Section 503 of the Rehabilitation Act, visit the U.S. Department of Labor’s Office of Federal Contract Compliance Programs (OFCCP) website at Yes, I Have A Disability, Or Have A History/Record Of Having A Disability No, I Don’t Have A Disability, Or A History/Record Of Having A Disability I Don’t Wish To Answer #J-18808-Ljbffr ADVANCED TELEMETRY SYSTEMS INT