O&M Instrument Controls & Electrical Technician

Job Description Summary The ICE Tech must troubleshoot, install and repair electrical systems, electrical / electronic control components of gas turbine, steam turbine, generator and balanced plant mechanical equipment to provide the customer with electrical power. Job Description Essential Responsibilities: The O&M Instrument Controls & Electrical Technician must also be fluent with various controls software programs including Rosemount / Emerson DCS, Mark VIe gas & steam turbine controls, various PLCs and local area networks. The power generation and supporting equipment includes gas turbine, steam turbine, diesel engines, generators, triple pressure heat recovery steam generator, air compressors, motors, pumps and motor control centers. As the O&M Instrument Controls & Electrical Technician you will: Diagnose cause of electrical, electronic malfunction or failure of operational equipment such as transformers, motors, relays, switches, and control and monitoring devices. Must be able to communicate findings to all interested parties Install wire and conduit for existing and newly installed machines and equipment Terminate wiring to machines and equipment, and connects cables and wires between machines and equipment Replace faulty wiring and electrical components of machines such as relays, switches, motors, and position sensing devices Diagnose, test, repair or replace faulty electronic components, such as printed circuit boards Replace electric motor bearings Test faulty equipment and applies knowledge of functional operation of electronic units and systems to diagnose cause of malfunction Align, adjust, and calibrate equipment according to specifications Maintain records of repair, calibrations, and tests conducted Connect unit to be tested to test equipment such as signal generator, frequency meter, or spectrum analyzer Understand proper use of electrical and electronic test equipment, read dials or digital displays that indicate electronic characteristics such as voltage, frequency, distortion, inductance, and capacity Read meters and gauges or automatic recording devices at specified intervals to verify proper operation Record maintenance actions taken on work order forms Open and close valves as required for proper system operation and mechanical isolation Open and close circuit breakers for proper system operation and electrical isolation Dismantle devices to gain access to and remove defective parts Start devices to test their performance Identify required spare parts for various plant systems Initiate purchase order for parts Read and understand technical manuals and system piping and instrumentation diagrams Make changes to wiring and piping and instrumentation diagrams using AutoCAD programs Perform preventative and corrective maintenance in accordance with technical manual procedures Prepare legible and understandable work orders for required preventative and corrective maintenance Read, understand, and comply with all plant safety and regulatory procedures Preserve and clean the control room electronic equipment, I & E shop, and all outside power systems Maintain, calibrate and repair Combustion Turbine Continuous Emissions Monitor (CEMS) and Data Acquisition System (DAS) for air permit compliance Maintain, calibrate and repair Combustion Turbine Remote Emissions Monitoring System (REMS) Prepare air emissions quarterly, semi-annual and annual reports Work with 3rd party contractors on various capital projects Must communicate effectively with employees at all levels of the organization Qualifications/Requirements : High School Diploma or GED Minimum of 2 years’ instrumentation & controls experience in combine or simple cycle power plant or related industrial environment Minimum of 2 years’ prior training and knowledge of Digital Control Systems and ability to use and modify computer programs Minimum 2 years’ experience in tuning DCS, control loop troubleshooting and design Minimum 2 years’ electrical and instrumentation aptitude involving the operation, troubleshooting / maintenance of industrial equipment, preferably of the type used in a combined cycle power plant Minimum 1 year of computer skills for data analysis, including MS Office products including email and Internet Eligibility Requirements Ability and willingness to work extended shift hours, call outs, holidays, weekends and overtime Desired Characteristics GE Mark VI control systems, GE Fanuc PLC Electrical, Instrumentation or Controls technical certificates or certifications Knowledge of CMMS software Familiarity with NERC standards and requirements Familiar with gas turbine and steam turbines Proficiency in running rigid conduit, SST tubing and wiring pulling Demonstrated ability to read and interpret electrical, mechanical process drawings and P&ID's Demonstrated communication skills at all levels Ability to write routine reports and correspondence Able to work alone or with help to diagnose and correct electrical, instrumentation and controls problems About Us For U.S. based candidates only, for purposes of complying with U.S. pay transparency requirements, the base pay range for this position is $50-$60 per hour. The specific pay offered may be influenced by a variety of factors, including the candidate’s experience, education, and skill set. The Company pays a geographic differential of 110%, 120% or 130% of salary in certain areas. This position will stay open on the career website until at least January 29, 2026. Benefits Available to You: GE employees rise to the challenge of building a world that works. We provide varied, competitive benefits to help support our workforce: this posting does not include external links. Equal Opportunity Employer. Employment decisions are made without regard to race, color, religion, national or ethnic origin, sex, sexual orientation, gender identity or expression, age, disability, protected veteran status or other characteristics protected by law. Relocation Assistance Provided: Yes #J-18808-Ljbffr GE Vernova