Liaison Engineer 4

We are seeking Senior Liaison Engineers to support the Portland, Oregon site. We are looking for a proactive individual who can make prompt engineering decisions and who want to go beyond their desk and into the factory for hands on engineering. This position requires excellent communication and collaboration skills as the candidate will be partnering closely with production personnel. The candidate will be the engineering representative on the factory floor transforming design into reality. This position is fully onsite. Position Responsibilities Analyzes, conducts root cause analysis and develops dispositions for production non-conformances. Applies knowledge of Company design principles to assess and resolve product/process issues through the product lifecycle. Applies engineering principles to research technical, operational and quality issues in support of executing final engineering solutions. Identifies documents, analyzes reported problems and communicates deviations that could impact design intent and safety; recommends and manages resolution. Develops and implements product/process improvements. Supports Integrated Product Teams (IPT) and participates in design reviews. Represents the engineering community from initial build through the production and post-production environment. Ensures supplier and build partner compliance with Company standards. Develops customer correspondence for continued safe operation and maintenance of equipment. Participates in on-site disabled product repair teams, accident investigation and support teams. Analyzes damage repair or structural modification to determine appropriate jacking and shoring, prevent collateral damage and assure a safe work environment. Designs interim structural repairs and conducts static strength analysis. Develops non-destructive test procedures, tools and standards. Shift: This position is for multiple shifts and may require off shift, weekend, and travel assignments. The candidate may periodically be assigned to first, second, or third shift as well as weekend or daily overtime. This requirement varies from site to site and is typically covered on a rotation basis. Requirements Basic Qualifications (Required Skills/Experience): Bachelor's or Masters of Science Degree from an ABET OR ABET equivalent accredited course of study in Engineering 10 or more years of experience in structures, systems, design, or production engineering (Senior- Level). 5+ years of experience in prior Materiel Review Board Preferred Qualifications (Desired Skills/Experience): Liaison engineers that have experience across the following, will be looked for: Understanding for materials Material types - steel, aluminum, titanium - strength/capabilities Material forms – bar stock, forgings, castings and reactions to machining Post machining processing Understanding machining and machining limitations Geometry and sequencing for material removal (multiple pass, speed and feed of cutter) Machine practices – machining, broaching, honing, etc Load path analysis for complex, integrated shapes – thin walls, undercuts, mismatches Surface condition and prep – discoloration, burns, drill/cutter breaks (FOD) Understanding of machined part dimensions and tolerance (GD&T) GD&T – True position, parallel surface, bonus tolerance, etc - used heavily (GD&T training 77100 Course – minimum) Interpret drawing datums, surfaces, profiles for tolerancing Examples - requirements between gear/shaft fit up into housings, fit up of housing sections (base and cover) Spatial Analyzer analysis/modeling of discrepant conditions Metrology - methods, limitations, and interpretation Understanding of gears/shafts and gear interaction Gear table understanding Details - Teeth/spline profiles, runout, measurement over wires Install – gear patterns, gear engagement, bearing/shaft fit Understanding of material processing Heat treat, induction hardening, stress relief Shot and glass peening, abrasive blast cleaning, etching Plating – cad, chrome, Zi-Ni Finishing – anodize, passivate, primer and paint sequence Understanding functional test requirements Diagnosing impacts to operation and performance at the airplane level Range of FT acceptance – RPM, Torque, gaps/clearance Understanding of general repair for machined parts •M bushings, heli-coils, and inserts on oversized bores and holes Blending on machined materials, re-processing, re-finishing requirements Corrosion protection post processing rework - seal and primer requirements Education/experience typically acquired through advanced technical education from an accredited course of study in engineering, computer science, mathematics, physics or chemistry (e.g. Bachelor) and typically 9 or more years' related work experience or an equivalent combination of technical education and experience (e.g. PhD+4 years' related work experience, Master+7 years' related work experience). In the USA, ABET accreditation is the preferred, although not required, accreditation standard. CTS Pays For Referrals! Refer a friend or colleague to join our team and enjoy fantastic rewards through our referral program. Contact us today to learn more!! Discover Our Benefits At CTS, we offer a comprehensive benefits package to support our employees, including: Comprehensive healthcare coverage Paid time off Retirement savings plans Learn more about our benefits! Position Id : 377134 Status : Closed Location : Portland, Oregon Duration : 12+ months Pay Rate : Up to $86.00/Hour Employment Type : Contract Work Shift : Willing to work any shift #J-18808-Ljbffr Cts Technology Solutions, Inc.