Structural Welders and Fitters

Job Description

Job Description

This position is at a shipyard in central Houston!

Plenty of work, plenty of Overtime!

Day and night-shift available

Entry level from welding school graduate's excepted. $18-$20 an hr based on testing results

Weld Test: Read Carefully to make sure you can pass

• Take 2 unbeveled Carbon Steel plates and set the desired gap. There is no minimum or maximum gap that has to be used. Welder’s preference.
• Once gap is set, the welder will then put a small tack at each end of the plates in so they bond to each other.
• The welder will then mark a line in the center of the plates to designate the 3G (Vertical) side from the 4G (Overhead) side.
• Next, the welder will tack their test plate in the 3G position.
• Using a 6011 electrode with a 5/32” diameter, the welder will run an uphill pass to seal off the gap between the 2 plates, fusing them together.
• NOTE: The welder is not required to penetrate all the way through to the backside of the test plate.
• inspected for holes and quality of composition.
• After the pass of 6011 has been inspected, the welder will take a 7018 electrode with a 1/8” diameter and run a single weave pass on top of the pass of 6011 that is already
• present creating the cap of the weld.
• After the pass of 7018 is complete, the welder will clean off the excess slag to have it visually inspected for discrepancies such as undercut, porosity, and overall
• appearance.
• If the welder’s 3G test is acceptable, they will then proceed to tack their test plates in the 4G position.
• Once the welder has tacked their test plates, they will once again, take a 6011 electrode with a 5/32” diameter and run a single pass to seal off the gap between the 2 plates, fusing them together
• NOTE: The welder is not required to penetrate all the way through to the backside of the test plate.
• Once the welder has completed a single pass with a 6011 5/32” electrode, they will clean off the excess slag with a wire brush and chipping hammer to have the weld
• inspected for holes and quality of composition.
• After the pass of 6011 has been inspected, the welder will take a 7018 electrode with a 1/8” diameter and run two stringer passes on top of the pass of 6011 that is already
• present creating the cap of the weld.
• After the 2 passes of 7018 are complete, the welder will clean off the excess slag to have it visually inspected for discrepancies such as undercut, porosity, and overall appearance.

Job Summary

We are seeking a skilled and dedicated Welder specializing in Structural Shielded Metal Arc Welding (SMAW) to join our fabrication team. The successful candidate will be responsible for executing high-quality welds on structural steel components, adhering to strict safety and quality standards. This role offers an opportunity to work on diverse construction and fabrication projects, utilizing advanced welding techniques and mechanical knowledge. The ideal applicant will demonstrate proficiency in interpreting technical drawings, measuring instruments, and fabrication shop practices, contributing to the successful completion of complex metal structures.

Duties

• Perform structural welding using Shielded Metal Arc Welding (SMAW) techniques according to blueprints, technical drawings, and AWS standards.
• Read and interpret mechanical blueprints, fabrication drawings, and technical specifications to ensure precise assembly and welding.
• Measure materials accurately with calipers, micrometers, and measuring instruments to meet project specifications.
• Use power tools, hand tools, plasma cutters, and gas metal arc welding (GMAW) equipment for cutting, shaping, and assembling metal components.
• Fabricate metal structures by cutting, fitting, aligning, and welding sheet metal and structural steel parts.
• Maintain safety protocols at all times by adhering to construction site safety procedures and wearing appropriate personal protective equipment.
• Collaborate with team members on assembly processes, machining tasks, and quality inspections to ensure structural integrity.
• Utilize blueprint reading skills for interpreting technical drawings related to construction site projects and mechanical fabrication.
• Operate cranes or other lifting devices when necessary for handling heavy materials or assemblies.
• Conduct shop math calculations for measurements, angles, and material estimations during fabrication processes.

Qualifications

• Proven experience in construction site environments with a focus on structural steel welding.
• Proficiency in Shielded Metal Arc Welding (SMAW), with additional skills in MIG (GMAW) and TIG welding preferred.
• Strong understanding of AWS welding standards and safety protocols applicable to construction and fabrication settings.
• Ability to interpret mechanical blueprints, technical drawings, and construction plans accurately.
• Familiarity with measuring instruments such as calipers, micrometers, and tape measures for precise measurements.
• Mechanical knowledge of metal materials including sheet metal fabrication and structural components.
• Experience operating power tools, plasma cutters, cranes, and other fabrication equipment safely.
• Knowledge of shop math principles for accurate measurements and calculations related to fabrication tasks.
• Construction site experience with an emphasis on safety compliance and teamwork.
• Basic math skills necessary for measurements, calculations, and blueprint interpretation.
• Ability to work efficiently in a fast-paced environment while maintaining high-quality standards.

If you are a motivated professional with a strong background in structural welding and fabrication practices seeking a challenging opportunity to contribute your skills within a dynamic team environment, we encourage you to apply today.

RSC is a great company to work for! They treat they're employees right.

Company Description

RSC is a great company to work for! They treat they're employees right.