Quality Technician

Quality TechnicianCrane Aerospace & Electronics supplies critical systems and components to the aerospace and defense markets. Located in the epicenter of United States aviation manufacturing, our Crane Aerospace & Electronics Lynnwood, Wash., facility delivers industry-leading aerospace & defense power, sensing and fluid solutions. You'll join a group of aerospace professionals committed to engineering excellence and work in a community tucked between the idyllic Puget Sound and Cascade Mountains. Start the next chapter of your career with Crane Aerospace & Electronics!Job SummaryQuality Technicians are responsible for conformity inspection, source inspection, auditing, documenting, reviewing and recommending manufacturing process improvements, mentoring/training/assisting inspectors, DMIR activitiesEssential FunctionsEvaluate products and processes in accordance with engineering drawings, samples, inspection requirements, process specifications, procedures and other approved reference sources to verify complianceObtain certification (ex: AS13001 Supplier Self Release Training) for and perform customer DQR source inspection and FAA DMIR activitiesReceive training as needed to conduct Coordinate Measurement Machine (CMM) programming and back up duties for inspectionAssist in the preparation, review and approval of First Article Inspection Reports (FAIRs)Perform internal audits to comply with internal and customer guidelines. Develop checklists to be used as guidelines for audits from process specifications, work instructions, quality inspection procedures, corporate procedures, and industry or military specificationsEvaluate products for defective or damaged components, accurate assembly, fit, adjustment, dimensions, locations, identifications, cleanliness, finishes, wire routing, encapsulation, and other conditions, pertinent to acceptable sub-assemblies, assemblies, and end itemsObserve work in process and determine compliance to operational guidelines specified in process specifications, work instructions, quality inspection procedures, heat treat log verifications and other internal and contractual requirementsPerform defect data sorting, reporting and trending functions to facilitate identification areas or trends requiring corrective action. Prepare NCRs or Corrective Actions as neededDebrief appropriate levels of management from production leads to managers apprising them of acceptable and unacceptable activities and make viable recommendations for solution of problems when requestedTraining: Provide manufacturing operators and delegated inspectors with inspection skills, process measurement skills and serve as a resource for inspection issues. Train and instruct others in tactical processes.Any other tasks assigned by supervisor or managementBecome certified to AS13001Minimum QualificationsExperience: 1-7 years of experience in a manufacturing environmentKnowledge: Knowledge of basic mechanical and electrical measurement tools) or the ability to learn is desired; Knowledge of performing manufacturing process audits and feedback for process improvementSkills/Abilities: Understand, interpret, relate and instruct others on internal, industry or customer specifications which relate to products and processes which are performed and audited; Experience and/or training in process auditing.Education/Certification: High School Diploma or equivalent.Eligibility Requirement: This position may require access to Controlled Data or Information. Where the position requires such access only US Persons will be considered. As a US Department of Defense contractor, we are bound by International Traffic in Arms Regulations (ITAR).Preferred QualificationsPrior work as a technician, quality inspector, supervisor, or senior production operatorAssociates of Science degree or BA, BS degreeWorking ConditionsStandard office environmentWorking conditions are normal for a manufacturing environmentManufacturing operations may require the use of safety equipment to include but not limited to: eye safety glasses, gowning, masks, hearing protectors, heel/wrist straps and any other required PPEMay be exposed to unusual environmental conditions such as loud noises, cold temperatures, confined spaces, dust or fumesRequires work with small to medium size hand and power toolsOccasional travel to customer and outside test lab facilities for technical interchange meetings, design reviews, product testing support, and to attend technical seminarsMay need to travel domestically and internationally (up to 10%)Standing: 10% *percentage is approximate and may vary depending on work taskSitting: 90% *percentage is approximate and may vary depending on work taskLifting (in pounds): up to 20 poundsPushing (in pounds): up to 20 poundsMental/Visual: use of computer, calculator, filing cabinetsWorkspace: cubicle/desk/labTop BenefitsBenefits: Health care, dental, vision, life and disability insurance starting the first day of the month following your start date.Time Off: 15 days of paid time off that start accruing your first day at Crane plus 12 paid holidays per year.401k Retirement Plan: 401k plan with company match.Education Reimbursement: eligible after 6 months of employmentCrane Company. is an Equal Opportunity Employer. All qualified applicants will receive consideration for employment and will not be discriminated against on the basis of race, color, religion, gender, sexual orientation, general identity, national origin, disability or veteran status.