Ironworker
Commercial Steel Erection
Ironworker (Full Time)
Location: Madison Heights
Department: Steel Erection Summary Works as member of crew to raise, place, and unite beams, columns, and other structural steel members to form completed structures or structure frameworks in a safe and consistent manner by performing the following duties.
Essential Duties and Responsibilities include the following. Other duties may be assigned.
1. Has practical knowledge of Regulatory Compliance with local, state, and federal Occupational Safety and Health Administration (OSHA), CSE, Inc. Rules and Regulations and Site-Specific Rules and Regulations. a. Understands OSHA standards relating to Steel Erection; understands and complies with CSE, Inc. Safety Program, rules, regulations and updates.
b. Works within AISC Certification Procedures.
c. Trained to safely operate forklifts, JLG type man-lifts, scissor-lifts and similar equipment.
d. Observes 100% of tie-offs.
2. Follows directions and assumes responsibility of job essentials by: a. Assisting with inspecting and identifying hazards associated with operations.
b. Assuming control of tools and equipment operated.
c. Setting up hoisting equipment for raising and placing structural steel members.
d. Fastening steel members to cable of hoist with wire rope or nylon slings.
e. Unloading incoming steel, shakes out members and placing in lay down area.
f. Knowing OSHA signals and if assigned, signals worker operating hoisting equipment to lift and place steel member.
g. Assisting in set-up and knock-down of cranes.
h. Bolting up structural steel members, welding, and otherwise assembling.
i. Placing and securing metal deck components.
j. When working above ground uses safety harness, lanyard, and beamer for proper tie-off.
Supervisory Responsibilities : None.
Qualifications : To perform this job successfully, an individual must be able to perform each essential duty safely and satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. US CITIZENSHIP AND A FEDERAL BACKGROUND CHECK IR REQUIRED.
Education and/or Experience : One - two years experience.
Language Skills: Ability to read and interpret documents such as safety rules, operating and maintenance instructions, and procedure manuals.
Mathematical Skills: Ability to add and subtract two digit numbers and to multiply and divide with 10's and 100's.Ability to perform these operations using units of American money and weight measurement, volume, and distance.
Reasoning Ability: Ability to apply common sense understanding to carry out instructions in written, oral, or diagram form. Ability to deal with problems involving several concrete variables in standardized situations.
Certificates, Licenses, Registrations : Valid driver's license.
Other Qualifications Must be able to travel. Must be able to pass a pre-employment drug screen.
Physical Demands : The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is regularly required to stand; walk; use hands to finger, handle, or feel; reach with hands and arms; climb or balance; stoop, kneel, crouch, or crawl and talk or hear. The employee must regularly lift and /or move up to 50 pounds, frequently lift and/or move up to 100 pounds and occasionally lift and/or move more than 100 pounds.
Work Environment: The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is regularly exposed to wet and/or humid conditions; moving mechanical parts; high, precarious places; fumes or airborne particles and outside weather conditions. The employee is occasionally exposed to vibration. The noise level in the work environment is usually loud. The employee is usually exposed to significant heights and small ledges.
CSE offers competitive wages, vacation/personal time, medical, dental, vision, and other competitive benefits, including a 401k plan.
INTENT AND FUNCTION OF JOB DESCRIPTIONS Job descriptions assist organizations in ensuring that the hiring process is fairly administered and that qualified employees are selected.They are also essential to an effective appraisal system and related promotion, transfer, layoff, and termination decisions.Well-constructed job descriptions are an integral part of any effective compensation system.
All descriptions have been reviewed to ensure that only essential functions and basic duties have been included.Peripheral tasks, only incidentally related to each position, have been excluded.Requirements, skills, and abilities included have been determined to be the minimal standards required to successfully perform the positions.In no instance, however, should the duties, responsibilities, and requirements delineated be interpreted as all inclusive.Additional functions and requirements may be assigned by supervisors as deemed appropriate.
In accordance with the Americans with Disabilities Act, it is possible that requirements may be modified to reasonably accommodate disabled individuals.However, no accommodations will be made which may pose serious health or safety risks to the employee or others or which impose undue hardships on the organization.
Job descriptions are not intended as and do not create employment contracts.The organization maintains its status as an at-will employer.Employees can be terminated for any reason not prohibited by law.
I,
JS_8.1.3,JS_8.1.3.1,JS_8.1.3.5,JS_8.1.5,JS_8.1.5.1,JS_8.1.5.2,JS_8.1.5.3,JS_8.1.5.4,JS_8.2.1,JS_8.2.1.1,JS_8.2.1.2,JS_8.2.1.3,JS_8.2.1.4,JS_8.2.1.5,JS_8.2.2,JS_8.2.2.1,JS_8.2.2.2,JS_8.2.2.4,JS_8.2.3,JS_8.2.3.2,JS_8.2.3.3,JS_8.2.6,JS_8.2.6.1,JS_8.2.5,JS_8.2.5.1,JS_8.2.5.4,JS_8.2.5.6,JS_8.3.3,JS_8.3.3.1,JS_8.3.3.5,JS_8.3.5,JS_8.3.5.1,JS_8.3.5.2,JS_8.4.2,JS_8.4.2.3,JS_8.4.2.2,JS_8.4.2.4,JS_8.4.3,JS_8.4.3.1,JS_8.4.3.2,JS_8.4.3.3,JS_8.4.3.4,JS_8.4.4,JS_8.4.4.1,JS_8.4.4.2,JS_8.4.4.3,JS_8.4.4.4,JS_8.4.4.5,JS_8.4.5,JS_8.4.5.1,JS_8.4.5.2,JS_8.4.5.3,JS_8.5.6,JS_8.5.6.1,JS_8.5.6.2,JS_8.5.6.3,JS_8.5.6.4,JS_8.5.6.5,JS_8.5.7,JS_8.5.7.1,JS_8.5.7.2,JS_8.5.7.3,JS_8.5.7.4,JS_8.5.8,JS_8.5.8.1,JS_8.5.8.2,JS_8.5.8.3,JS_8.5.8.4,JS_8.5.8.5,JS_8.5.8.6,JS_8.5.9,JS_8.5.9.1,JS_8.5.9.2,JS_8.5.9.3,JS_8.5.9.4,JS_8.5.9.5,JS_8.5.10,JS_8.5.10.1,JS_8.5.10.2,JS_8.5.10.3,JS_8.5.10.4,JS_8.5.11,JS_8.5.11.1,JS_8.5.11.2,JS_8.5.11.3,JS_8.5.11.4,JS_8.5.12,JS_8.5.12.1,JS_8.5.12.2,JS_8.5.12.3,JS_8.5.12.4,JS_8.5.1,JS_8.5.1.1,JS_8.5.1.2,JS_8.5.1.3,JS_8.5.1.4,JS_8.5.2,JS_8.5.2.1,JS_8.5.2.2,JS_8.5.2.3,JS_8.5.3,JS_8.5.3.1,JS_8.5.3.2,JS_8.5.3.3,JS_8.5.3.4,JS_8.5.3.5,JS_8.5.4,JS_8.5.4.1,JS_8.5.4.2,JS_8.5.4.3,JS_8.5.4.4,JS_8.5.4.5,JS_8.5.4.6,JS_8.5.5,JS_8.5.5.1,JS_8.5.5.2,JS_8.5.5.3,JS_8.5.5.4,JS_8.5.5.5
Location: Madison Heights
Department: Steel Erection Summary Works as member of crew to raise, place, and unite beams, columns, and other structural steel members to form completed structures or structure frameworks in a safe and consistent manner by performing the following duties.
Essential Duties and Responsibilities include the following. Other duties may be assigned.
1. Has practical knowledge of Regulatory Compliance with local, state, and federal Occupational Safety and Health Administration (OSHA), CSE, Inc. Rules and Regulations and Site-Specific Rules and Regulations. a. Understands OSHA standards relating to Steel Erection; understands and complies with CSE, Inc. Safety Program, rules, regulations and updates.
b. Works within AISC Certification Procedures.
c. Trained to safely operate forklifts, JLG type man-lifts, scissor-lifts and similar equipment.
d. Observes 100% of tie-offs.
2. Follows directions and assumes responsibility of job essentials by: a. Assisting with inspecting and identifying hazards associated with operations.
b. Assuming control of tools and equipment operated.
c. Setting up hoisting equipment for raising and placing structural steel members.
d. Fastening steel members to cable of hoist with wire rope or nylon slings.
e. Unloading incoming steel, shakes out members and placing in lay down area.
f. Knowing OSHA signals and if assigned, signals worker operating hoisting equipment to lift and place steel member.
g. Assisting in set-up and knock-down of cranes.
h. Bolting up structural steel members, welding, and otherwise assembling.
i. Placing and securing metal deck components.
j. When working above ground uses safety harness, lanyard, and beamer for proper tie-off.
Supervisory Responsibilities : None.
Qualifications : To perform this job successfully, an individual must be able to perform each essential duty safely and satisfactorily. The requirements listed below are representative of the knowledge, skill, and/or ability required. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. US CITIZENSHIP AND A FEDERAL BACKGROUND CHECK IR REQUIRED.
Education and/or Experience : One - two years experience.
Language Skills: Ability to read and interpret documents such as safety rules, operating and maintenance instructions, and procedure manuals.
Mathematical Skills: Ability to add and subtract two digit numbers and to multiply and divide with 10's and 100's.Ability to perform these operations using units of American money and weight measurement, volume, and distance.
Reasoning Ability: Ability to apply common sense understanding to carry out instructions in written, oral, or diagram form. Ability to deal with problems involving several concrete variables in standardized situations.
Certificates, Licenses, Registrations : Valid driver's license.
Other Qualifications Must be able to travel. Must be able to pass a pre-employment drug screen.
Physical Demands : The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is regularly required to stand; walk; use hands to finger, handle, or feel; reach with hands and arms; climb or balance; stoop, kneel, crouch, or crawl and talk or hear. The employee must regularly lift and /or move up to 50 pounds, frequently lift and/or move up to 100 pounds and occasionally lift and/or move more than 100 pounds.
Work Environment: The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is regularly exposed to wet and/or humid conditions; moving mechanical parts; high, precarious places; fumes or airborne particles and outside weather conditions. The employee is occasionally exposed to vibration. The noise level in the work environment is usually loud. The employee is usually exposed to significant heights and small ledges.
CSE offers competitive wages, vacation/personal time, medical, dental, vision, and other competitive benefits, including a 401k plan.
INTENT AND FUNCTION OF JOB DESCRIPTIONS Job descriptions assist organizations in ensuring that the hiring process is fairly administered and that qualified employees are selected.They are also essential to an effective appraisal system and related promotion, transfer, layoff, and termination decisions.Well-constructed job descriptions are an integral part of any effective compensation system.
All descriptions have been reviewed to ensure that only essential functions and basic duties have been included.Peripheral tasks, only incidentally related to each position, have been excluded.Requirements, skills, and abilities included have been determined to be the minimal standards required to successfully perform the positions.In no instance, however, should the duties, responsibilities, and requirements delineated be interpreted as all inclusive.Additional functions and requirements may be assigned by supervisors as deemed appropriate.
In accordance with the Americans with Disabilities Act, it is possible that requirements may be modified to reasonably accommodate disabled individuals.However, no accommodations will be made which may pose serious health or safety risks to the employee or others or which impose undue hardships on the organization.
Job descriptions are not intended as and do not create employment contracts.The organization maintains its status as an at-will employer.Employees can be terminated for any reason not prohibited by law.
I,
JS_8.1.3,JS_8.1.3.1,JS_8.1.3.5,JS_8.1.5,JS_8.1.5.1,JS_8.1.5.2,JS_8.1.5.3,JS_8.1.5.4,JS_8.2.1,JS_8.2.1.1,JS_8.2.1.2,JS_8.2.1.3,JS_8.2.1.4,JS_8.2.1.5,JS_8.2.2,JS_8.2.2.1,JS_8.2.2.2,JS_8.2.2.4,JS_8.2.3,JS_8.2.3.2,JS_8.2.3.3,JS_8.2.6,JS_8.2.6.1,JS_8.2.5,JS_8.2.5.1,JS_8.2.5.4,JS_8.2.5.6,JS_8.3.3,JS_8.3.3.1,JS_8.3.3.5,JS_8.3.5,JS_8.3.5.1,JS_8.3.5.2,JS_8.4.2,JS_8.4.2.3,JS_8.4.2.2,JS_8.4.2.4,JS_8.4.3,JS_8.4.3.1,JS_8.4.3.2,JS_8.4.3.3,JS_8.4.3.4,JS_8.4.4,JS_8.4.4.1,JS_8.4.4.2,JS_8.4.4.3,JS_8.4.4.4,JS_8.4.4.5,JS_8.4.5,JS_8.4.5.1,JS_8.4.5.2,JS_8.4.5.3,JS_8.5.6,JS_8.5.6.1,JS_8.5.6.2,JS_8.5.6.3,JS_8.5.6.4,JS_8.5.6.5,JS_8.5.7,JS_8.5.7.1,JS_8.5.7.2,JS_8.5.7.3,JS_8.5.7.4,JS_8.5.8,JS_8.5.8.1,JS_8.5.8.2,JS_8.5.8.3,JS_8.5.8.4,JS_8.5.8.5,JS_8.5.8.6,JS_8.5.9,JS_8.5.9.1,JS_8.5.9.2,JS_8.5.9.3,JS_8.5.9.4,JS_8.5.9.5,JS_8.5.10,JS_8.5.10.1,JS_8.5.10.2,JS_8.5.10.3,JS_8.5.10.4,JS_8.5.11,JS_8.5.11.1,JS_8.5.11.2,JS_8.5.11.3,JS_8.5.11.4,JS_8.5.12,JS_8.5.12.1,JS_8.5.12.2,JS_8.5.12.3,JS_8.5.12.4,JS_8.5.1,JS_8.5.1.1,JS_8.5.1.2,JS_8.5.1.3,JS_8.5.1.4,JS_8.5.2,JS_8.5.2.1,JS_8.5.2.2,JS_8.5.2.3,JS_8.5.3,JS_8.5.3.1,JS_8.5.3.2,JS_8.5.3.3,JS_8.5.3.4,JS_8.5.3.5,JS_8.5.4,JS_8.5.4.1,JS_8.5.4.2,JS_8.5.4.3,JS_8.5.4.4,JS_8.5.4.5,JS_8.5.4.6,JS_8.5.5,JS_8.5.5.1,JS_8.5.5.2,JS_8.5.5.3,JS_8.5.5.4,JS_8.5.5.5
Vacancy posted 1 day ago
Similar jobs that could be interesting for youBased on the Ironworker in Madison Heights, MI vacancy
- Combo Pipe Welder (Full Time) Location: Madison Heights Department: Steel Erection Department : Piping and Rigging Reports To : Piping Project Manager FLSA Status : Non-Exempt Summary : Multi-process Combo Welder with a strong...SuggestedFull time
Commercial Steel Erection
Madison Heights, MI4 days ago - Application Instructions Apply Online or In Person! Position Description Future Fabricating is an AISC certified commercial ornamental fabrication company. We provide unique and specialized fabricated items needed to complete a variety of architectural and...SuggestedApprenticeship
Future Fence Company
Warren, MI3 days ago - Welder - 1st Shift Job Category: Operations Requisition Number: WELDE006634 Posted: June 25, 2026 Full-Time On-site Barnes Aero Warren | 0149 25250 Easy St Warren, MI 48089, USA Description Key Responsibilities: Prepare materials for welding;...SuggestedFull timeWork at officeLocal areaDay shift
Barnes Inc.
Warren, MI3 days ago - Welders - All Shifts Barnes Aerospace offers competitive wages, shift differentials, 401k savings plan, paid time off, holidays, and much more! We're more than a company, we're a team. When you join our team, you'll be part of an innovative, industry-renowned provider...SuggestedWork at officeImmediate startRelocation packageAll shiftsShift work
Barnes Inc.
Warren, MI4 days ago $50 per hour
PCSI is seeking a Pipefitter to join its Mechanical department. Responsibilities include installation, repairs, and maintenance of high‑pressure steam, hydronic heat, chilled water, and plumbing systems across a military facility. This role involves reviewing as‑built ...SuggestedHourly payContract workFor contractorsMonday to FridayShift workPCSI - Professional Contract Services, Inc
Warren, MI2 days ago- The Pipefitter is responsible for layout and fabrication, assembly, installation, and maintenance ofpiping/plumbing systems, fixtures and equipment for steam, water, sprinkler, heating, cooling, lubricatingand related systems. This work requires practical journeyman level...
Stellantis
Warren, MI5 days ago - The Pipefitter is responsible for layout and fabrication, assembly, installation, and maintenance of piping/plumbing systems, fixtures and equipment for steam, water, sprinkler, heating, cooling, lubricating and related systems. This work requires practical journeyman ...ApprenticeshipWork at officeRelocationShift work
Stellantis
Warren, MI1 day ago $18 per hour
Who We Are For more than 75 years, Douglas Dynamics has been North America’s premier manufacturer and upfitter of commercial work truck attachments and equipment. Our family of industry-leading brands – FISHER® , SnowEx® , WESTERN® , HENDERSON® , DEJANA® , and VENCO VENTURO...Hourly payFull timeFlexible hoursDouglas Dynamics
Madison Heights, MI1 day ago- A leading aerospace manufacturing company is seeking Welders across various locations including Warren, MI. This role involves preparing materials, inspecting welds, and ensuring quality standards. Candidates should possess a high school diploma, at least 1 year of welding...
Barnes Inc.
Warren, MI2 days ago $27 - $32 per hour
Description Tradesmen International is looking to expand our team of qualified Trade Professionals for current & future projects in and around Warren, MI. Most positions are first shift with a pay scale of $27-32/hour based on experience & skill level. If you are a Welder...Day shift- Job Description Job Summary: The welder is responsible for fitting and welding aluminum parts using a MIG and/or TIG process. Also required to perform other miscellaneous tasks, as assigned by his supervisor. Set up welding machines based on the job at hand and using a...
- Job Description We are seeking a skilled and detail-oriented Aluminum Welder / Fabricator to join our production team. In this role, you will read blueprints, cut raw materials, and utilize TIG and MIG welding techniques to build high-quality aluminum products. The ideal...Immediate start
- Brasco International in Madison Heights, Michigan is seeking a qualified welder responsible for fitting and welding aluminum parts using MIG and/or TIG processes. Responsibilities include setting up welding machines, reading blueprints, and ensuring work adheres to safety...
- Flex-N-Gate Stamping, 27027 Groesbeck Hwy, Warren, Michigan, United States of America Job Description Posted Thursday, June 18, 2026 at 4:00 AM General Summary Requires ability to operate Mig Welding equipment and perform production Mig Welding on medium to heavy parts...Flexible hours
- Position Summary Barton Malow is seeking a Re-Steel Fabricator to work out of our Oak Park, MI field operations. The Re-Steel Fabricator is responsible for operating fabrication machinery and equipment under the direction of the Fabrication Foreman to support the production...
- Meatcutting Worker Serves as the Meatcutting Worker in a Defense Commissary Agency (DeCA) location. The primary purpose of this position is to assist full performance meatcutters by performing the simpler tasks when processing beef, pork, veal, and lamb into retail ...
US Government Jobs
Warren, MI2 days ago - Job Title Position responsibilities include: Assist journeyman meat cutters by performing the simpler tasks when processing beef, pork, veal, and lamb into retail and ready to eat cuts for sale to patrons. Tray, wrap, weigh, and price cuts using automatic or...
US Department of War
Warren, MI3 days ago - Tig Welder M-F 6:00am - 3:30pm Some Saturdays, typically 6am-12pm Regular overtime opportunities, customer anticipates roughly 45 hours a week, (5 hours of OT) MUST BE ABLE TO READ BLUEPRINTS AND UNDERSTAND WHAT THEY NEED TO DO BASED OFF OF THEM Job Summary: ...
MCM Staffing
Madison Heights, MI5 days ago - The Juris Agency is seeking a skilled Aluminum Welder / Fabricator in Madison Heights, Michigan. This role requires mastery of TIG and MIG welding techniques to create high-quality aluminum products. Ideal candidates should have a minimum of 2-3 years of welding experience...
$32 per hour
A leading workforce solutions provider is seeking a Welder/Fabricator in Warren, MI. The role involves MIG, TIG, and structural welding, with pay ranging from $27 to $32 per hour based on experience. Candidates must have their own basic tools and appropriate PPE (Hood and...Hourly pay- Barton Malow is looking for a Re-Steel Fabricator in Oak Park, MI, responsible for operating machinery and ensuring quality in fabricated steel for construction projects. This role emphasizes safety and organization within the fabrication shop. The ideal candidate will ...
$13.5 per hour
Assembler, B Shift We currently have openings for assemblers in our plant in Warren, MI. We are looking for general assemblers for B Shift (Wednesday - Saturday 4:30 pm - 3:00 am) starting at $13.50 an hour. Team Members are eligible for benefits the 1st of the month following...Shift workNight shiftWestern Capital Resources
Warren, MI2 days ago- Complete assembly of automotive seating units Develop proficiency in all production job functions and rotate in job cell into various work stations Control processing, delivery or installation of nonconforming product until deficiency or unsatisfactory condition has been...
Adient
Warren, MI1 day ago $13.25 per hour
A leading automotive assembly company in Warren, MI is hiring general assemblers for A Shift (Monday - Thursday 5:00 am - 3:20 pm) with a starting pay of $13.25 an hour. Responsibilities include assembling automotive components, maintaining a safe working environment, ...Shift workDay shiftAvancez LLC
Warren, MI1 day ago$70k - $80k
MagTech is currently hiring a Shop Foreman in Warren, MI. This is a DIRECT HIRE position. Please apply below if you are interested and meet the qualifications below! Responsibilities: The Shop Foreman is responsible for the development, coaching and leadership...Permanent employmentFor contractorsCurrently hiringDay shiftMAG-TECH INC
Warren, MI3 days ago- Our company is seeking a skilled TIG Welder/Fabricator to join our team. The successful candidate will be responsible for fitting and welding aluminum parts in the manufacturing of transit shelters. We pride ourselves on maintaining a safe and quality-focused work environment...
Air Comfort Corporation
Madison Heights, MI1 day ago - Stellantis is hiring a full-time Pipefitter in Warren, Michigan. The role requires layout, fabrication, and maintenance of plumbing systems, with at least 4 years of relevant experience or apprenticeship completion. Candidates should be able to work with blueprints, possess...Full timeApprenticeshipWork at officeRelocation
$50 per hour
PCSI - Professional Contract Services, Inc is seeking a skilled Pipefitter to join its Mechanical department in Warren, MI. The successful candidate will handle high-pressure steam, chilled water, and plumbing systems maintenance within a military facility. Responsibilities...Hourly payContract work$16 per hour
From Entry-Level to Executive, Find Your Next Career. Interested in joining our talent pool? We are always accepting applications! Please note : This listing remains open even when we are not actively hiring. We review resumes continuously for future opportunities...Hourly payWeekly paySeasonal workLocal areaImmediate startCrown Staffing Solutions LLC
Warren, MI1 day ago$21.38 - $22.68 per hour
General Information Name Assembly Worker - Relocate to Roseau MN Employment Type Temporary Position level Full-time Virtual/Remote? No Labor Category Light Industrial Date ...Weekly payFull timeTemporary workLocal areaImmediate startRemote workRelocationFlexible hoursShift workRotating shiftDay shiftAfternoon shiftKelly Services, Inc.
Warren, MI5 days ago
Do you want to receive more vacancies?
Subscribe and receive similar vacancies to Ironworker. Be the first to apply!
