Process Engineer

Vulcan Elements is manufacturing American rare-earth permanent magnets for a secure, resilient future. With a focus on national security and economic resiliency, we serve critical industries such as defense, aerospace, and automotive powering a high-technology future. Vulcan Elements is building a team of ambitious professionals committed to Mission Focus, Technical Excellence, and Transparency. As a Process Engineer, you will contribute to the full lifecycle of a massive 1million square foot manufacturing facility expansion—from design and equipment specification through installation, commissioning, production startup, and scale-up to full capacity. You will be responsible for a process step, translating pilot-line processes into full-scale, stable, and repeatable production systems. This is a high-impact, high-ownership role requiring deep technical expertise and leadership. Core Expectations & Responsibilities Run engineering trials todetermineoptimalequipment recipes and operating windows. Own the parameter definition required to transition processes from development to stable, high-volume production. Identify the best ways to operate manufacturing equipment to maximize yield, improve throughput, and minimize scrap. Monitor OEE results and station cycle times to drive continuous improvement. Lead Gage R&R studies and capability studies (Cpkanalysis) to ensure equipment and measurement systems are capable of meeting tight product specifications. Lead and own the PFMEA (Process Failure Mode and Effects Analysis) for your designated process steps to proactively identify and mitigate product and process risks. Provide hands-on support during production startup, helping operators stabilize processes and eliminating early bottlenecks. Dedicate time to reviewing physical product quality at the station level, mapping defects back to root causes in the machinery or process settings. Ensure compliance with safety, environmental, and quality standards across all process activities. This position will require some interaction and travel to support equipment development reviews and Factory Acceptance Tests (FATs) as needed (estimated at You will also be responsible for developing, reviewing, or managing the following deliverables: Risk Assessments, Ergonomic Assessments, and PFMEA. Process Flow Charts, Bill of Process (BOP), Station Cycle Times, Process Sheets, and Process Checklists. Quality Control Plans, R&R (Gage Repeatability and Reproducibility) Studies, and Quality Checklists. Standard Operating Procedures (SOPs), Work Instructions, Calibration Procedures, and Process Monitoring plans. Input on HMI Controls logic, MES Transactions Lists, and process parameters tracking. Qualifications Bachelor’s degree in Chemical Engineering, Materials Science, Industrial Engineering, Mechanical Engineering, or a related technical discipline with 3 + years of experience. DeepexpertiserunningDoEs(Design of Experiments), Gage R&R studies, and statistical process control (SPC) tooptimizehigh-precision manufacturing processes. Expert-level experience authoring and developing standard manufacturing documents (PFMEA, Control Plans, Work Instructions, and Process Flows). Proventrack recordof designing and running on-floor production trials to dial in complex equipment parameters without causing excessive downtime. Desired Skills Experience specifically in heavy industrial manufacturing, metallurgy, magnetics, or chemical processing. Six Sigma Green Belt or Black Belt certification. Familiarity with MES (Manufacturing Execution Systems) implementation and automated transaction mapping. Experience in highly regulated industries such as Defense (DoD), Aerospace (AS9100), or Automotive (IATF 16949). Physical and Environmental Requirements The position requires regular presence on the production floor and the ability to navigate all areas of the facility. Candidates must be able to climb stairs, stand and walk for extended periods, and work in environments that may be hot, humid, or noisy. The role also requires the use of personal protective equipment, including respirators, and adherence to all applicable safety policies, procedures, and regulatory requirements. Employees must be able to complete required fit testing, wear appropriate PPE for the duration of assigned tasks, and respond safely to changing conditions within the production environment. Voluntary Self-Identification For government reporting purposes, we ask candidates to respond to the below self-identification survey.Completion of the form is entirely voluntary. Whatever your decision, it will not be considered in the hiringprocess or thereafter. Any information that you do provide will be recorded and maintained in a confidential file. As set forth in Vulcan Elements’s Equal Employment Opportunity policy,we do not discriminate on the basis of any protected group status under any applicable law. If you believe you belong to any of the categories of protected veterans listed below, please indicate by making the appropriate selection.As a government contractor subject to the Vietnam Era Veterans Readjustment Assistance Act (VEVRAA), we request this information in order to measurethe effectiveness of the outreach and positive recruitment efforts we undertake pursuant to VEVRAA. Classification of protected categoriesis as follows: A "disabled veteran" is one of the following: a veteran of the U.S. military, ground, naval or air service who is entitled to compensation (or who but for the receipt of military retired pay would be entitled to compensation) under laws administered by the Secretary of Veterans Affairs; or a person who was discharged or released from active duty because of a service-connected disability. A "recently separated veteran" means any veteran during the three-year period beginning on the date of such veteran's discharge or release from active duty in the U.S. military, ground, naval, or air service. An "active duty wartime or campaign badge veteran" means a veteran who served on active duty in the U.S. military, ground, naval or air service during a war, or in a campaign or expedition for which a campaign badge has been authorized under the laws administered by the Department of Defense. An "Armed forces service medal veteran" means a veteran who, while serving on active duty in the U.S. military, ground, naval or air service, participated in a United States military operation for which an Armed Forces service medal was awarded pursuant to Executive Order 12985. Voluntary Self-Identification of Disability We are a federal contractor or subcontractor. The law requires us to provide equal employment opportunity to qualified people with disabilities. We have a goal of having at least 7% of our workers as people with disabilities. The law says we must measure our progress towards this goal. To do this, we must ask applicants and employees if they have a disability or have ever had one. People can become disabled, so we need to ask this question at least every five years. How do you know if you have a disability? Alcohol or other substance use disorder (not currently using drugs illegally) Autoimmune disorder, for example, lupus, fibromyalgia, rheumatoid arthritis, HIV/AIDS Blind or low vision Cancer (past or present) Cardiovascular or heart disease Celiac disease Cerebral palsy Deaf or serious difficulty hearing Diabetes Disfigurement, for example, disfigurement caused by burns, wounds, accidents, or congenital disorders Epilepsy or other seizure disorder Gastrointestinal disorders, for example, Crohn's Disease, irritable bowel syndrome Intellectual or developmental disability Mental health conditions, for example, depression, bipolar disorder, anxiety disorder, schizophrenia, PTSD Missing limbs or partially missing limbs Mobility impairment, benefiting from the use of a wheelchair, scooter, walker, leg brace(s) and/or other supports Nervous system condition, for example, migraine headaches, Parkinson’s disease, multiple sclerosis (MS) Neurodivergence, for example, attention-deficit/hyperactivity disorder (ADHD), autism spectrum disorder, dyslexia, dyspraxia, other learning disabilities Partial or complete paralysis (any cause) Pulmonary or respiratory conditions, for example, tuberculosis, asthma, emphysema Short stature (dwarfism) Traumatic brain injury PUBLIC BURDEN STATEMENT: According to the Paperwork Reduction Act of 1995 no persons are required to respond to a collection of information unless such collection displays a valid OMB control number. This survey should take about 5 minutes to complete. #J-18808-Ljbffr Vulcan-Elements