Instrumentation Tech

Instrumentation TechCleveland - Cleveland, OH 44103OverviewSalary Range $29.05 Position Type Full Time Job Shift 1st Shift Education Level HS Diploma or GED Travel Percentage None Category ManufacturingDescriptionSUMMARYThe Instrumentation Technicians is responsible for the maintenance, repair, tuning, and calibration of combustion systems throughout the facility. Such systems include, but are not limited to pneumatics, hydraulics, steam, gas, and minor refractory. Required skills include, but are not limited to general mechanical repair, electrical controls repair, minor PLC programming, and minor refractory repair.ESSENTIAL DUTIES AND RESPONSIBILITIESEnsure furnaces are maintained to meet requirements of AMS 2750 and other customer imposed pyrometry requirements.Set up, conduct, and document required system accuracy testing per standards and SIFCO work instructions.Set up, conduct, and document required temperature uniformity surveys per standards and SIFCO work instructions.Calibrate all equipment instrumentation including, but not limited to, temperature controllers, HMIs, PLC systems, thermocouples, and data recorders.Troubleshoot furnace performance issues and conduct repairs in support of operations. Work with Combustion Control operators to troubleshoot and improve furnace accuracy and reliability.Set furnace temperatures and combustion ratios as back up for Combustion Control technicians as assigned.Perform required preventative maintenance work described in workorder management system. Change out resident and non-resident thermocouples as scheduled based on SIFCO work instructions.Ensure Maintenance logs are accurate and signed off by the Quality and department managers.Replace and/or repair equipment controllers, HMI screens, back-up recorders, and other PLC equipment.Monitor reliability and performance of combustion systems: Complete periodic manometer pressure testing on combustion systems to ensure equipment uniformity is correct and running stoichiometric.Utilize combustion analyzer to monitor biproducts of combustion gases produced while running product.Monitor door condition and conduct thermography to ensure minimal heat loss.Log all Thermocouple certifications to be approved by designated Quality members.Maintain detailed knowledge of the current revisions of AMS2750 and Work Instructions assigned.Maintain a detailed knowledge on the current revisions of NFPA86 – Standard for Ovens and Furnaces.All other duties as assigned.SUPERVISORY RESPONSIBILITIESThis job has no supervisory responsibilities, but indirect oversight and training of combustion control is expected.QualificationsTo perform this job successfully an individual must be able to perform each essential duty satisfactorily. The requirements listed below are representative of the knowledge, skill and/or ability required. Reasonable accommodations may be made to enable individuals with disability to perform the essential functions.EDUCATION and/or EXPERIENCEHigh school diploma or general education degree (GED); or one to three months related experience and/or training; or equivalent combination of education and experience. Air/Gas ratio, instrumentation. Understanding of AMS 2750 and associated requirements is preferred, and will be trained as part of the classification criteria.LANGUAGE SKILLSAbility to read and comprehend simple instructions, short correspondence and memos. Ability to write simple correspondence. The ability to effectively present information in one-on-one and small group situations to customers, clients and other employees of the organization.MATHEMATICAL SKILLSAbility to add, subtract, multiply and divide in all units of measure using whole numbers, common fractions and decimals. Ability to compute rate, ratio and percent and to draw and interpret bar graphs.REASONING ABILITYAbility to apply common sense understanding to carry out detailed but uninvolved written or oral instructions. Ability to deal with problems involving a few concrete variables in standardized situations. Ability to make correction decisions on furnace capabilities.CERTIFICATES, LICENSES, REGISTRATIONSCombustion Training – Basic ElectricalPHYSICAL DEMANDSThe physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.While performing the duties of this job, the employee is regularly required to stand, use hands to finger, handle or feel and reach with hands and arms; and talk or hear. The employee frequently is required to walk, climb or balance. The employee is occasionally required to sit and stoop, kneel, crouch or crawl. The employee must occasionally lift and/or move up to 75 pounds and frequently lift up to 50 pounds. Specific vision abilities required by this job include close vision, distance vision, color vision, peripheral vision, depth perception and ability to adjust focus.WORK ENVIRONMENTThe work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.While performing the duties of this job, the employee is frequently exposed to extreme heat. The noise level in the work environment is usually loud.We believe a workforce with diverse backgrounds, skills and experiences helps us reach our goals and realize our full potential. We may have different ways of approaching problems, but we solve them together with a focus on our Core Values of Integrity, Responsiveness, Respect and Passion.SIFCO has a competitive compensation and benefits package, including medical, dental, vision, life insurance, disability, flexible spending accounts, supplemental insurance, and a 401(k) plan with a generous match.If you need assistance with the application process due to a disability, please email