NONDESTRUCTIVE TESTER Jobs

Nondestructive TesterDuties As a NONDESTRUCTIVE TESTER, WG-3705-10, this position is located in the Aircraft Structural Maintenance Section of an Air National Guard aircraft Maintenance Group, Maintenance Squadron, Fabrication Flight. This is an Air National Guard (ANG) Dual Status Technician position requiring military membership, compatible military skill assignment, and classification. The primary purpose of this position is to inspect aerospace weapon systems components and support equipment for structural integrity using nondestructive inspection methods and performs fluid analysis.1. Determines test method, and prepares fluids and parts for nondestructive inspection. Interprets nondestructive inspection test results, and provides information about defects to repair center. Performs Oil Spectrometry process and analyzes wear metal content on engine lubricating oil and other fluids, and recommends corrective action. Establishes radiation areas for radiographic operations. Computes and monitors personal exposure areas for radiographic operations, and monitors personnel exposure data.2. Performs nondestructive inspection on structures, components, and systems. Detects flaws such as cracks, delaminations, voids, processing defects, and heat damage using penetrant, eddy current, magnetic particle, radiographic, optical, Thermography, Shearography and ultrasonic test equipment. Determines metallurgical information of components according to alloy, temper, conductivity, and associated factors. May also serve as Alternate TMDE Monitor, PCAMS, Alternate Equipment Custodian, Alternate Supplies Manager, Alternate Hazardous Waste Monitor, Alternate Hazardous Communication Monitor, Alternate Spill Prevention Monitor, Alternate FOD Monitor, Alternate Radiation Monitor, Alternate Technical Order Monitor, Alternate Precious Metals Monitor, and Training Monitor.3. Applies magnetic particle and/or liquid penetrant inspection to detect and interpret the relevancy of flaws in a variety of parts. Parts are numerous and varied, and are of ferrous and/or nonferrous metals, and consist of surface or near surface discontinuities in the metal; e.g., fatigue cracks, welding overlap, cold shut, or surface cracks that may stem from internal flaws, such as pipes, inclusions, or forging lap. Sets up each different liquid penetrant or magnetic particle method following Technical Orders (TOs), Time Change Technical Orders (TCTOs), or Work Control Documents (WCDs), or Nondestructive Testing Instructions (NDIs). Ensures the equipment and solutions are in compliance with technical guides and quality standards before performing tests and must submit an AFTO 22 if defects in TO's exist or an AF 107 if there is no technical data to accompany the task. Performs all processing tasks; i.e., dipping items in penetrant or magnetic particle baths, washing and drying, magnetizing and demagnetizing ferrous items, and subjecting them to Ultra Violet Black light to detect and evaluate flaws, their nature, size, scope, and exact location. If items are repairable, records test results, and marks defect areas and dimensions. Initiates WCDs that specify the needed repairs. Re-inspects all repairs performed on each component upon their return to the shop.4. Uses and maintains tools. Maintains bench stock levels of parts, materials, tools, and equipment at prescribed levels. Uses tools and equipment associated with testing being conducted in the shop, as well as hand and power tools to do the work.5. Utilizes safety practices and procedures following established safety rules and regulations to maintain a safe and clean work environment. Uses and assures proper fit of required Personal Protective Equipment and clothing. Follows federal and state rules when storing, using, handling, labeling, and disposing of hazardous materials and waste in accordance with environmental standards. Performs clean-up duties, such as cleaning equipment, sweeping, straightening, and lining up tools and other property in the assigned area.6. Maintains records and documents actions. Manually documents actions taken or enters information into an automated system. Obtains required coordination and signatures.7. Performs other duties as assigned. *The above description only mentions a limited amount of the position's official duties. For a full comprehensive document that covers all the duties of the position, please contact one of the Recruitment Specialists at the bottom of the announcement.Requirements Conditions of employmentNational Guard Membership is required.Males born after 31 December 1959 must be registered for Selective Service.Participation in direct deposit is mandatory.U.S. citizenship is required.This position is covered by the Domestic Violence Misdemeanor Amendment (30 Sep 96) of the Gun Control Act (Lautenberg Amendment) of 1968. An individual convicted of a qualifying crime of domestic violence may not perform the duties of this position.The duties of this job may significantly impact the environment. You are responsible to maintain awareness of your environmental responsibilities as dictated by legal and regulatory requirements, your organization, and its changing mission.Must be able to establish effective professional working relationships with coworkers and customers, contributing to a cooperative working environment and successful accomplishment of the mission.May occasionally be required to work other than normal duty hours; shift work and/or overtime may be required.Federal employment suitability required and determined by a background investigation before appointment to position.May be required to successfully complete a trial period.Must have a valid driver's license.Must be able to obtain/maintain the necessary security clearance for the position.Military Assignment Requirement: Open to Enlisted members onlyMilitary Rank/Grade Requirement: Minimum Rank A1C/E-3 to Maximum Rank SSgt/E-5Compatible Military AFSC Requirement: 2A752This is not a cross training opportunity.Technicians are required to perform annual task evaluations on each inspection duty in order to maintain certification.Qualifications Areas of Consideration: Area 1 - Current permanent and indefinite T32 technicians of the Oregon ANG. Area 2 - Current permanent and indefinite T5 employees of the Oregon ANG. Area 3 - Current service members in the Oregon ANG. GENERAL and SPECIALIZED EXPERIENCE QUALIFICATION REQUIREMENTS: Work involves nondestructive examination of metals, composites, ceramics, plastics, and other materials for internal and external structural defects, delamination's, corrosion, and moisture penetration using magnetic particle, liquid penetrant, eddy current, radiographic, ultrasonic, or other types of nondestructive test processes and equipment. Experience or training which demonstrates the ability to set up and operate test equipment, use test apparatus to apply tests to material or products, record readings, observe and record established reactions, and classify according to defined categories. WG-09 and above - Must have 18 months experience or training in using ultrasonic and/or eddy current inspection techniques to observe, measure, and detect discontinuities and flaws. Experience classifying test results, identifying material deficiencies, and recommending courses of action for items of equipment. Experience recommending engine components to be inspected and forwarding results to the appropriate authority. Experience performing scheduled inspections of testing equipment ensuring compliance with established technical regulations and procedures. Education No education requirement associated with this position.Additional information The following applies to Bargaining Unit Positions: Bargaining unit positions within the Oregon National Guard that are represented by AFGE, local 2986 (AFL-CIO). If you are a male applicant who was born after 12/31/1959 and are required to register under the Military Selective Service Act, the Defense Authorization Act of 1986 requires that you be registered or you are not eligible for appointment in this agency ( ) group id: DOAF