Setup Technician

POSITION SUMMARYSetup and teardown, including all ancillary equipment, of injection molds from the injection molding machines. Care and maintenance of injection molds between production runs.ELEMENTS RELATED TO THE FUNCTIONPosition Type: Non-ExemptSchedule: Monday – Friday, 2:30pm – 11:00pm; $3.00 Shift DifferentialLocation: DEMGY Pacific, LLC, Tacoma WAPHYSICAL REQUIREMENTSThe physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.While performing the duties of this job, the employee regularly is required to stand for 10 to 12 hours; walk; sit; use hand to finger, handle, or feel objects, tools or controls; reach with hands and arms; balance; stoop; talk and hear. The employee will occasionally lift and/or move up to 50 pounds. Specific vision abilities required by the job include ability to see with 20/20 vision to assess cosmetic requirements, close vision, peripheral vision, depth perceptions, and the ability to adjust focus.APPLICABLE METRICSAdhere to the Demgy Pacific attendance point systemAdhere to the Demgy Pacific job variance to standard metricAdhere to the Demgy Pacific Safety protocolsLabor reporting percentage (daily avg)Labor reported within BOM setup times, vs labor outside of setup times (should be a ratio)Setup completion %. (measure of whether they miss anything and how often – Should be a percentage, measured by a periodic inspection check sheet)Damaged tooling/equipment on setup or teardown (number of instances).JOB RESPONSIBILITIESSETUP TECHNICIAN IInstall tooling dies (molds) into injectionVerify, molds and ancillary equipment are safely setup and functioning properlyRemoval of ancillary equipment from work centers after production runs are completeClean molds/equipment and store in a safe protected conditionUse a variety of hand tools in an appropriate and safe mannerOperate a pallet jackRecord time spent on tasksKeep work areas clean and organizedOperate (machines) while caring for equipment and toolsConduct resin handling, drying, and movementMaterial dryer operation and cleaningMold heater setup and operationVerification and documentation of all mold/equipment setup processesVerification and documentation of all equipment parametersOperation of injection molding machine in “Setup Mode”Red tag broken or unsafe tools and equipmentOther duties as assignedSETUP TECHNICIAN IIOperate ForkliftTrain Material Handler (Mold floor)Train Mold Setup (Level 1)Issue MRO work orders for damaged/malfunctioning equipmentInstallation and verification of position switches on all features of a toolProper setup of vacuum verification on toolingCorrectly install an additive feeder on an injection molding machineEffectively “Purge” an injection molding machine following the SOP’s providedAt least 1.5 years at Demgy Pacific, or equivalent manufacturing scenarioPerform simple, Core/Cavity, insert changesTrain Mold Setup (Level 2)Operate Reach truckOther duties as assignedEMPLOYEE RESPONSIBILITIESUphold and comply with Demgy’s Code of Ethics and ConductFollow safety policiesContribute to the success of the company’s environmental, health & safety programMaintain a positive working relationship with co-workers in all departmentsMaintain accurate documentation as required, following Demgy Pacific’s document and record control procedures as applicable to the positionEnsure that housekeeping within the department is properly maintained.Follow Demgy 5S program (workstation organization/locations maintained)Follow policies outlined in the Employee HandbookPerform other duties as directed by the supervisorJOB SKILL REQUIREMENTSEffective communication:o Able to read and write English.o Able to keep accurate quality records.o Able to basic math (addition, subtraction, multiplication, and division)Mechanical skills.Basic computer skills.Team oriented.Efficient and action driven.Motivated self-starter.Dependable: Reliable attendance and punctuality.MINIMUM EDUCATION AND QUALIFICATIONSSuccessful completion or proven prior experience required as a Setup Technician in Injection Molding to qualify to move from Setup Technician I to Setup Technician II to Setup Technician III.Experience in manufacturing, preferred.Experience in Aerospace, preferred.High School diploma or equivalent. #J-18808-Ljbffr