CNC Operator Day shift

Primary Purpose of this Position: Fabricate parts for structural fabrication, Service Center, and miscellaneous steel assemblies per cutting lists, shop drawings, and DWS quality requirements. Essential Job Functions: Identify steel shapes, sizes, and mill tolerances. Fabricate material as trained and instructed. Fabricate beams, tubes, angle, channel, bar grating, pipe, plate, or rounds according to the dimensions shown on cut lists and shop drawings, AISC code requirements for structural steel, and machine capabilities. Make adjustments to machine to ensure accurate dimensions as shown on the shop drawings. Identify cut list and shop drawing errors and discrepancies before or during early stages of fabrication. Operate forklifts, jib cranes, overhead cranes, conveyors, and transfers to move materials. Any other duties assigned by management. Attend all meetings as required by management. Consistently and reliably work scheduled hours at assigned locations. Qualifications (Knowledge, Skills and Abilities): Ability to read, write, and perform higher arithmetic computations involving addition, subtraction, multiplication, and division of whole numbers, decimals and fractions. Ability to understand and carry out semi‑complicated verbal and written instructions. Ability to effectively communicate with co‑workers, supervisors, and managers. Ability to work under periodic supervision focused on the progress of work and setting priorities for job completion. Skill in using auto measurer, tape measure, or 1” rule. Ability to pass a Drake‑Williams Steel administered test that covers shop drawing interpretation, fractional number calculations, basic geometry, etc. Ability to interpret, understand and utilize cutting lists, shop orders, and shop drawings. Ability to use a computer for cut‑lists and inventory purposes. Ability to possess pride in own workmanship; demonstrate attention to detail, and work safely. Ability to operate forklifts and overhead cranes in a safe and proper manner. Use and understand industry and Drake‑Williams Steel adopted hand signals used for crane operations. Perform minor mechanical tasks on machine (blade changes, cleaning, etc.). Ability to follow inventory procedures. Ability to multi‑task. Physical Demands: Stand frequently over the course of the 8 to 12 hour work shift. Walk occasionally to frequently over the course of the 8 to 12 hour work shift; distances range from a few feet to 60 feet. Sit only during break and lunch periods. Lift weights up to 20 pounds from floor to chest continuously. Lift weights up to 35 pounds from floor to waist frequently during the shift. Lift weights up to 60 pounds from floor to waist occasionally; jib cranes and overhead cranes are available. Carry weights described over distances of a few feet to 60 feet. Climb occasionally onto or over conveyors. Stoop or crouch occasionally; position held continuously for 2 to 15 minutes depending on the job. Kneel occasionally depending on the job. Crawl rarely up to 10 feet to access tools, materials, etc. Reach forward occasionally to retrieve tools or perform job duties. Reach overhead occasionally to guide material attached to the cranes or attach chains. Push and pull drawers open occasionally to frequently to retrieve tools. Push material occasionally into machine for fabrication (SHEAR). Gross finger dexterity skills required to operate the various tools and equipment. Non‑Material Handling Demands: Employee is expected to work 40 hours a week; overtime and weekends may be required. Hearing sufficient to be aware of safety issues. Visual ability to read and interpret shop drawings. Safety glasses are required. Exposure to heat, cold, wet, and humid conditions occasionally. Exposure to fumes, odors and dusts occasionally. Exposure to solvents, greases, oils, and coolants occasionally. Wear all required PPE: steel‑toe safety shoes, hearing protection, safety glasses, gloves, and hard hats. Tools Required: Pencil, square, tape measure, markers, ball peen hammer, wire brushes, 4” grinder, sledgehammer, grab hooks, vise grips, Allen wrenches, pry‑bar, C‑clamps, band cutters, and chains. Machines Utilized: Saw, overhead crane, jib crane, pallets, transfers, brake, blaster, punch, shear, and forklifts. Experience and Education Required: High School degree or equivalent. Minimum six months of experience in a steel manufacturing environment. #J-18808-Ljbffr