Process Engineer

Process Engineer

Country


United States of America

State / County


Utah

City


Ogden

Division


Structurals

Company


Ogden

Function


Engineering

Workplace Type


On-Site

Position type


Full Time

Opportunity ID


23007

Job Description

Primary Function: Responsible for determining operations to produce product and develop processes to ensure quality, cost, increase productivity, and reduce cycle time, and scrap.

Principle Duties and Responsibilities:

Process Control

• Writes work instructions, procedures and techniques.
• Review and implementation of customer supplied drawings and specification flow down.
• Analyzes problems and develops solutions with minor technical direction.
• Designs fixturing for self-identified operation improvements.
• Update and review KPIV control charts, control limits.
• Reviews changes of incoming raw materials and evaluates for potential process impact.
• Review, monitor and improve tooling/equipment.
• Designs new tooling for process improvements with additional Engineering support.
• Collects, processes, mines, and interprets data and implements improvements based on analysis.
• Designs and oversees process experiments to determine the causes of defects and improve process methods and raw materials.
• Supports junior Engineers

Reduce Variability (Continuous Improvement)

• Improves measurements and capabilities for raw materials, input variables, process yields, and response variable using statistical process control (SPC) and never-ending improvement (NEI) methods. Focuses on key department metrics such as scrap, rework, and process yield.

• Improves the use and integration of SPC tools and techniques to improve process predictability.
• Conducts gauge repeatability and reproducibility studies to correct gauge error greater than 30%.
• Discusses and improves design issues, procedures, and techniques with departmental supervisor and product engineer.

• Reviews and controls process parameters.
• Reviews, designs and implements part set-ups/gating design to eliminate variability.
• Identifies and addresses safety considerations within the scope of the job/area responsibilities. Specifies and justifies major equipment purchases and building modifications.

Minimum Job Requirements:

• Bachelor's Degree in Engineering or a minimum of 2 to 5 years of experience.
• Able to work in a production environment.
• Able to read and comprehend English.
• Able to work with mathematical concepts such as probability and statistical inference, and plane and solid geometry and trigonometry. Able to apply concepts of fractions, percentages, ratios and proportions to practical solutions.

• Able to lift and carry up to 10 lbs. frequently.
• Able to lift and carry up to 35 lbs. occasionally.
• Able to communicate effectively with co-workers and customers.
• Able to effectively present information to management and customers.
• Able to define problems, collect data, establish facts, and draw valid conclusions. Able to interpret an extensive variety of technical instructions in mathematical or diagram form and deal with several abstract and concrete variables.

• Able to read, analyze and interpret general business periodicals, professional journals, technical procedures, or governmental regulations. Able to write reports, business correspondence, and procedure manuals.

• Vision expectation is Jaeger J1 in one eye, at no less than 12 inches: or equivalent, or Jaeger J2 in one eye, at no less than 16 inches.

• Able to use Microsoft Office applications.
• Complies with company and departmental policies and procedures, including company's attendance policy.

Desired Competencies:

• Blueprint & CMM inspection data interpretation
• Broad knowledge of mechanical, industrial, and materials science engineering

• 3-5 years experience with investment casting technology

Normal Working Conditions

• Works under general direction and infrequent supervision, planning details of procedure and methods to attain definite objectives. Makes decisions within broad limitations of policies and within accepted standards.

• Occasional work required near moving mechanical parts.
• Occasional work required in areas with fumes and/or airborne particles.
• Frequent work required in areas with loud noise.
• Occasional standing and walking required.
• Frequent sitting required. Frequent hearing and talking required

The above statements are intended to describe the general nature and revel of work being performed. They are not intended to be an exhaustive list of all duties, responsibilities, and skills.

Precision Castparts Corp. is an equal opportunity employer committed to recruit, hire, train, and promote in all job categories without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, age, disability, veteran status or other status protected by applicable law.


All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity, national origin, disability, or status as a protected veteran.

This position requires use of information or access to production processes subject to national security controls under U.S. export control laws and regulations (including, but not limited to the International Traffic in Arms Regulations (ITAR) and the Export Administration Regulations (EAR)). To be qualified to work in this facility, a successful applicant must be a U.S. Person, as defined in those regulations, and able to supply evidence of that qualification prior to starting work or be authorized to receive controlled information under a specific license or permission from the relevant government agency. The U.S. export control regulations define a U.S. person as a U.S. Citizen, U.S. National, U.S. Permanent Resident (i.e. 'Green Card Holder'), and certain categories of Asylees and Refugees.

This position requires use of information or access to production processes subject to national security controls under U.S. export control laws and regulations (including, but not limited to the International Traffic in Arms Regulations (ITAR) and the Export Administration Regulations (EAR)). To comply with those regulations, this position may require applicants to be U.S. Persons (i.e., U.S. citizens, U.S. lawful permanent residents, protected individuals as defined by 8 U.S.C. 1324b(a)(3)), or eligible to obtain the required export authorizations from the U.S. Department of State or the U.S. Department of Commerce.

Company Profile


With more than 120 operations and approximately 20,000 employees worldwide, Precision Castparts Corp. is the market leader in manufacturing large, complex structural investment castings, airfoil castings, forged components, aerostructures and highly engineered, critical fasteners for aerospace applications. In addition, we are the leading producer of airfoil castings for the industrial gas turbine market. We also manufacture extruded seamless pipe, fittings, and forgings for power generation and oil & gas applications; commercial and military airframe aerostructures; and metal alloys and other materials for the casting and forging industries. With such critical applications, we insist on quality and dependability - not just in the materials and products we make, but in the people we recruit.

PCC is relentless in its dedication to being a high-quality, low-cost and on-time producer; delivering the highest value to its customers while continually pursuing strategic, profitable growth.

In 2016, Berkshire Hathaway, led by Chairman and CEO Warren E. Buffett, acquired Precision Castparts Corp.

Precision Castparts Corp. and its affiliates do not accept unsolicited resumes from search firms or employment agencies. Unsolicited resumes will become the property of Precision Castparts Corp & its affiliates, and no fee will be paid.