Production Technician III

• • Identify Production Variance
    • Do so by utilizing Production Viewer, PI, Cygnet and other tools you see fit ensuring all wells are at or above clean average (target)
      • If wells are not at or above clean average, devise step by step plans and action them in attempt to get well back at or above CA.
      • If assistance is needed in getting a well/pad back to CA reach out to the following in this order
        1. Lead area tech
        2. Optimizer
        3. Production Foreman
  • Ensure metrics are met
    • Site inspections
      • Verify no overdue site inspections.
        • Use PBI tool to verify no site inspections are due.
    • Plunger inspections
      • Verify no overdue plunger inspections
        • Use PBI tool to verify plunger inspections are not outside of the below KPI's
          • 5000 miles or more
          • 12 months or older
    • Verifications/Gaps
      • Target verifications and gaps by using the COW tool along with SIMOPS in operation.
      • Verification to gap target % is a 15% ratio at an individual level annually.
    • Coding
      • Verify that all coding is done correctly and is up to date.
        • Normal Ops - No Action codes are true to bucket.
        • Base Backout - No Action coded wells have been verified that all basic troubleshooting steps have been checked off and well truly is underperforming due to line pressure increase.
        • Confirm all wells above clean average are assigned back to Normal Ops - No Action.
        • Follow up with lead area tech on codes that are in the engineering/optimization bucket longer than 7 days.
  • Field Assistance
    • Flex over to other areas of the field if your route is completed and metrics are met for the day.

• Basic requirements
  • Training and Expectations
    • Hold yourself accountable and ask your lead area tech, optimizer or production foreman for assistance, training or guidance on the following.
    • Plunger Lift
      • Ensure you have a basic understanding of plunger lift wells.
      • Ensure you understand how to perform plunger inspections.
        • Have calipers, plunger removal tool, SOP's and spare parts needed.
      • Ensure you know where to view the plunger programs and tools
        • Power BI plunger page.
        • Cygnet plunger tab.
        • Enbase plunger inspection process.
      • Troubleshooting plunger lift wells and verify all plunger lift troubleshooting guide steps have been done before coding it to optimization.
    • Gas Lift
      • Ensure you have basic knowledge of gas lift wells.
        • The correlation between casing and tubing pressure.
        • The importance of not over or under injecting.
        • How all surface equipment operates.
        • How to troubleshoot via Cygnet.
      • Ability to identify over/under injecting based on total well meter throughput and critical rate required.
    • Well head compression
      • Understand the basics of a well head compressor in conjunction with pulling on the well with no other type of AL.
    • Free Flowing Wells
      • Understanding of basics of free-flowing wells.
        • Casing wells
        • Tubing wells
        • OTAP wells
    • Electronic tools
      • Ensure you have access to and understand how to utilize tools listed below.
        • Cygnet
        • Production Viewer
        • Ops tool kit
        • Enbase
          • SORA
        • PI
        • Teams
        • Outlook
        • GIS

• • • Equipment (Facility dependent. Not all sites will have the following equipment)
      • Wellhead operation, maintenance, and troubleshooting.
      • Cooler operation, maintenance, troubleshooting and startup/shutdown.
      • HP/LP separator operation, maintenance, and troubleshooting.
      • Heater treater operation, maintenance, troubleshooting and startup/shutdown.
      • Blowcase operation, maintenance, and troubleshooting.
      • Compressor operation, maintenance, troubleshooting and startup/shutdown.
      • Suction scrubber operation, maintenance and troubleshooting.
      • Discharge scrubber, operation, maintenance and troubleshooting.
      • UF operation, maintenance and troubleshooting.
      • Chemical loop operation, maintenance, and troubleshooting.
      • Bullet H2S treater operation, maintenance, and troubleshooting.
      • Flash gas scrubber operation, maintenance, and operation.
      • Tank level management and bottoms recirc pump requirements.
      • GLV operation, and troubleshooting.
      • Air compressor operation, maintenance, troubleshooting and startup/shutdown.
      • Coalescer operation, maintenance, and troubleshooting.
      • Fuel gas system operation, maintenance, and troubleshooting.
      • SKO operation, maintenance, and troubleshooting.
      • Cellar and containment expectations and management.
      • Catalytic heater operation, maintenance and troubleshooting.
      • Control valve operation, maintenance and troubleshooting.

With over 90 years' combined experience, NES Fircroft (NES) is proud to be the world's leading engineering staffing provider spanning the Oil & Gas, Power & Renewables, Chemicals, Construction & Infrastructure, Life Sciences, Mining and Manufacturing sectors worldwide. With more than 80 offices in 45 countries, we are able to provide our clients with the engineering and technical expertise they need, wherever and whenever it is needed. We offer contractors far more than a traditional recruitment service, supporting with everything from securing visas and work permits, to providing market-leading benefits packages and accommodation, ensuring they are safely and compliantly able to support our clients.