Journeyman Electrician (Dallas, TX)

Journeyman ElectricianMorley Moss is hiring for the role of Journeyman Electrician in Dallas, TX. Safety is first and foremost. This position will coordinate with Foreman; procure resources, material, tools and documents required for the assigned project. Utilize the most cost effective and efficient means available to produce a safe and profitable project. Everything you say and do reflects the values of each member of the Morley Moss family. Performs all electrical tasks with general supervision, possesses journeyman license, can read blueprints, terminate cable, install and trouble shoot control wiring from drawings, is able to demonstrate experience factors exceeding an electrical helper, and must be sufficient on rough-in work. A Journeyman would normally have this classification for the first year and then be considered for potential field leadership roles as they become available.#morley#LI-KH1#LI-SJ1Essential Duties & ResponsibilitiesDuties include but are not limited to the following:Installing buss feedersWire and conduit sizingSwitchgear installation and terminationLayout and preparation for installationUnderground layout and rough-inTroubleshooting Motors and controlsEssential Job FunctionsSafetyProper tool use and maintenanceProvide feedback on helpers and assigned apprenticesSet positive examples for your teammatesHold your apprentices to a high standardBe accountable for self and hold your teammates accountableBe open to criticism and learn from it.Non-essential Job FunctionsInteraction with owner/contractorAssist Foreman and GF with daily dutiesIdentify better processesSelf-StarterMotivated and able to motivate othersHave a positive attitudeQualificationsRequirements5 years of JATC training or Equivalent TrainingHave a minimum of an active JIW license in the state of OklahomaMeet all established criteriaPhysical DemandsA Journeyman Electrician needs to be able to move freely and comfortably in various positions, including bending, stooping, kneeling, climbing, and working overhead or in confined spaces, with the ability to be able to identify and voice Hazards, so that the corrections and precautionary measures can be made to avoid poor ergonomics, or any type of incidents. This role involves a significant amount of physical activity and requires a good range of motion to effectively and safely perform job duties.Upper Extremities:Reaching: Extending hands and arms in any direction to access wiring, fixtures, and components in various locations.Grasping/Manipulating: Using hands and wrists for repetitive actions like grasping and manipulating tools and wiring. This includes working with hand tools (up to 25 pounds) in various positions, including above and below the head.Lifting/Carrying: Lifting and carrying objects weighing up to 60 pounds, including tools and equipment, and pushing/pulling up to 160 pounds. Lifting up to 50 pounds frequently.Lower Extremities and Trunk:Operate two (2) handed tools/equipment, cable cutters, hammer drills, compression tools, and jack hammers.Read and interpret maps, instructional manuals, specifications, work site directions, blueprints, and writteninstructions.Operate and work from mechanical personnel lifts (electric or gas powered).Supervise assigned job site employees to complete project.Standing/Walking: Maintaining a standing position for long periods of time while performing repetitive actions, such as grasping or manipulating tools. Prolonged standing and walking in an indoor/outdoor environment as applicable.Bending/Stooping: Bending legs at the knees to come to a rest on the knee or knees. Bending body downward and forward by bending the spine at the waist. Stooping and bending to reach valves.Kneeling/Crouching/Squatting: Performing tasks that require bending at the knees to rest on one or both knees. Squatting and crouching, at times, in confined tight spaces.Climbing: Climbing ladders, stairs, and working from aerial devices or platforms at heights of 6 feet or greater. Working on ladders and elevated platforms and in confined spaces.Crawling: Crawling through small tunnels that are hot, muddy, and wet.Twisting: Twisting the body and neck while operating company equipment.Balancing: Maintaining balance while working at heights or in awkward positions.All other duties as assignedAdditional Requirements:Able to effectively read and communicate in English.Positively identify colors of wires.Comprehends reading and drawing prints and schematicsBend conduit by hand with hand benders.Must use all power tools, saws, threaders, wire tuggers, hydraulic benders, and knockout punches.Capable of digging trenches, either by use of hand tools or power equipment.Operate equipment such as trenchers, backhoe, and lift trucks in a safe manner.Practices and comprehends safe work procedures as outlined in M.M. Safety Policy Handbook, Haz-Com Policy, and Lockout/Tagout Policy.Hand/Eye Coordination: Required for various tasks like working with tools and installing wiring.Specific Vision Abilities: Close vision (clear vision at 20 inches or less), distance vision (clear vision at 20 feet or more), peripheral vision (ability to observe an area that can be seen up and down or to the left and right while eyes are fixed on a given point), depth perception (three-dimensional vision, ability to judge distances and spatial relationships), and the ability to adjust focus (ability to adjust the eye to bring an object into sharp focus).Hearing: The ability to receive detailed information through oral communication and to make discriminations in sound, including audible alarms.Work EnvironmentThe work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.While performing the duties of this job, the employee may be regularly required to work outdoors, be exposed to wet and/or humid conditions; moving mechanical and electrical parts; high, precarious places; dust, fumes or airborne particles; toxic or caustic chemicals; outside weather conditions, extended exposure to sunlight; cold and heat; risk of electrical shock and vibration. The noise level in the work environment is usually moderate to loud.BenefitsGreat pay and benefits!Equal Opportunity EmployerAs a leading provider of mechanical and electrical construction, facilities services, and energy infrastructure, we offer employees a competitive salary and benefits package and we are always looking for individuals with the talent and skills required to contribute to our continued growth and success. Equal Opportunity Employer/Veterans/DisabledAffirmative Action PolicyPlease review our Affirmative Action Policy.Notice to Prospective EmployeesNotice to prospective employees: There have been fraudulent postings and emails regarding job openings. EMCOR Group and its companies list open positions here. Please check our available positions to confirm that a post or email is genuine. EMCOR Group and its companies do not reach out to individuals to help with marketing or other similar services. If an individual is contacted for services outside of EMCOR's normal application process – it is probably fraudulent.