Equipment Maintenance Technician - Front End Days (FED)

Position Summary Equipment Maintenance Technician IV is responsible for the maintenance of wafer fabrication assembly and facilities equipment for production lines. Responsible for troubleshooting and repairing downed equipment and assisting engineering staff in establishing and implementing periodic equipment maintenance. Uses test and diagnostic equipment to perform checkouts. Rebuilds manufacturing equipment. Technician may participate in safety forums, Emergency Response Teams and station improvement teams. Essential Job Functions Responsible for the maintenance of wafer fabrication assembly and facilities equipment for production lines. Responsible for troubleshooting and repairing downed equipment and assisting engineering staff in establishing and implementing periodic equipment maintenance. Responsible for scheduling and working with outside contractors for equipment maintenance covered by service contracts. Responsible for identifying PM’s to support stability of wafer fabrication assembly and facilities equipment for production lines with minimal assistance. Use test and diagnostic equipment to perform troubleshooting and repair wafer fabrication assembly and facilities equipment. Rebuilds manufacturing equipment as required. Provides training to other technicians and operators. Responsible for training of peers on process and operational improvement and equipment maintenance. Perform equipment modifications as directed by supervisors, managers and engineers. Determines methods and procedures on new assignments and may provide guidance to other nonexempt personnel. Collects and evaluates operating and process data and recommends means to improve operational processes. Works on assignments requiring considerable judgment and initiative. Understands implications of work and makes recommendations for solutions. Responsible for, and makes recommendations to, fulfill departmental quality, safety, quantity and teamwork requirements. May be required to ensure other technicians adhere to departmental quality, safety, quantity and teamwork requirements. Trained in proper handling of chemicals and hazardous waste. Supervisor Responsibility May provide guidance to other nonexempt personnel. Qualifications Required: High school degree or equivalent and 4-6 years of related experience. Experience working with one or more of the following: high vacuum equipment, lithography tools, wet benches and/or measurement equipment. Ability to troubleshoot, diagnose and repair wafer fabrication assembly and facilitate equipment for product lines, with minimal assistance. Basic computer skills including the use of standard office software, including Word, Excel and Outlook. Ability to work effectively as a member of a diverse team, as well as individually. Excellent verbal and written communication skills. Must be highly organized. Must be a self-starter and comfortable working in an ambiguous environment. Must be able to follow written and verbal instructions. Must be a fast-learner. Must be able to be trained in proper handling of chemicals and hazardous waste. Desired: Associate’s degree or higher. Past supervisor or lead experience. Physical Demands Standing or walking, use of hands to finger, handling, feeling, reaching with hands and arms, kneeling, crouching or crawling over two-thirds of the time. Lifting up to 25 lbs over two-thirds of the time. Must have normal color vision and must be able to identify wiring color codes. Work Environment Works in wafer fabrication and clean room environment, requiring clean room gowning (smock, hood, gloves, booties, etc.) Exposure to moderate noise levels. Exposure to stored energy hazards (electricity, compressed gases, etc.) Works in a facility that houses hazardous chemicals. May potentially handle hazardous waste in accordance with the safe work practices defined in Hazardous Communication and Hazardous Waste training programs. Initial training is required upon hiring status and every 3 years thereafter. Employees handling hazardous waste will insure that waste containers in their work areas are properly labeled and dated. Employees will ensure that waste containers are closed after transferring waste to them. Report any incidents involving hazardous waste to supervisor. Additional Information Other duties as may be assigned. Each employee’s primary objective is to assure that the quality, delivery and cost controls within his/her control meet or exceed all of our internal and external customers’ requirements. Each employee is required to abide by the Employee Handbook and the rules and regulations explained and provided at each orientation and training session. Special attention must be given to the safety aspects of these documents. Compensation & Benefits Pay rate for position: $32.00 - $45.00 per hour, commensurate with experience. Work schedule: Compressed Work Week - Front End Days - Every Sunday, Monday, Tuesday, and every other Wednesday. 5:30 am - 6:00 pm FUJIFILM Dimatix, Inc. provides competitive wages, a generous benefits package and a friendly, dynamic working environment. EEO Information Fujifilm is committed to providing equal opportunities in hiring, promotion and advancement, compensation, benefits, and training regardless of nationality, age, gender, sexual orientation or gender identity, race, ethnicity, religion, political creed, ideology, national, or social origin, disability, veteran status, etc. ADA Information If you require reasonable accommodation in completing this application, interviewing, completing any pre‑employment testing, or otherwise participating in the employee selection process, please direct your inquiries to our HR Department (View email address on click.appcast.io). Equal Opportunity Statement Equal Opportunity Employer Fujifilm Dimatix is an E-Verify Employer #J-18808-Ljbffr FUJIFILM Holdings America Corporation