Inspector

If you are unable to complete this application due to a disability, contact this employer to ask for an accommodation or an alternative application process. Inspector City of Industry, CA, US Salary Range: $20.00 To $25.00 Hourly Career Opportunity – Aerospace Quality Control Mechanical Inspector – Acromil LLC Using state-of-the-art technology, Acromil, LLC in City of Industry, CA has been a primary supplier to the Commercial and Defense Aerospace Industries of complex structural components and assemblies since 1959. Acromil pursues its vision of excellence by providing the highest quality products, on time and at competitive prices within a culture of integrity and pride. This vision led us to the acquisition of a similar business operation located in Corona, CA in September 2018 for a total footprint of 200,000 square feet. Acromil’s increased capacity will further our goal of being a World Class Supplier. The selected individual will be responsible for inspecting customer products to ensure products are manufactured within conformance of customer specifications; inspection includes, but is not limited to checking dimensions, tolerances, functionality, configuration, aesthetics, surface finish, or plating, and material per customer specifications and/or blueprints. Responsibility includes inspection of raw material, first articles, in process, source inspection, purchased, or modified products and complex assemblies. Sort and stack usable parts for shipping, document and contain defective parts for rework, customer submittal and necessary dispositioning. Responsibilities Perform complex mechanical dimensional and visual inspection of products or complex assemblies including first article, in-process and final inspections per blueprints and/or other written specifications using designated and appropriate measuring devices, such as micrometers, calipers, digital (dial) indicators, optical comparator, ring, pin or thread gages. Verify controls for precision tools and inspection equipment to regulate proper inspection of product and ensure calibration requirements are accurate and current. Document part numbers, lot numbers, serial numbers, quantities, inspection dates, results on manufacturing plans, AS9102 forms and all other associated documentation to ensure accurate product quality history records for each inspection task performed. Inspect product within the estimated time requirements. Assist Quality Control Management during investigations and/or deviations review. Support the requirements of the AS9100 Quality Management Systems. Report and communicate all non-conforming product(s) in accordance with established procedures. Monitor work order to ensure inspection and manufacturing operations are completed as required. Responsible for communicating and informing manufacturing and other related departments of any out of tolerance condition or acceptability of product based on specification. Perform general quality inspection tasks and other work-related duties as required or assigned by Quality Control Management. Strong communication skills are required to ensure suppliers understand requirements and expectations; make trip reports and present findings. Qualifications Experience with ANSI Y14.5 Geometric Tolerance. Understanding of aerospace drawings, specifications, processing, and quality requirements. Basic understanding of calibration requirements. Basic understanding of statistical process control. Experience with Excel, Word, and Outlook. Familiar with CMM operations (ability to run programs) Experience of AS9102 forms and related requirements. Person must be a United States (US) Person as defined by ITAR Regulations – A United States (US) Person is a citizen of the United States, a lawful permanent resident alien of the US, (a "Green Card" holder), a refugee or someone in the USA as a protected political asylee or under amnesty. Education & Experience High School diploma or GED; some college or technical training preferred. A minimum of three (3) years quality assurance mechanical inspection experience required, or a combination of education and/or experience. Must have experience using calipers, micrometers, height gauge, comparator, and knowledge of GD&T and blueprints. Knowledge of CMM, Romer and or Laser Tracker, Bill of Materials and MRP systems desired. Other Skills and Abilities Language Skills: Ability to read, interpret and adhere to written documents such as quality manual, inspection procedures, operating and maintenance instructions, blueprints, schematics and work instructions; the ability to write routine reports and correspondence and document inspections accurately. Must listen well to verbal instructions and seek clarification when necessary and respond concisely to inquiries from management or co-workers. Math Skills: Ability to add, subtract, multiply, and divide in all units of measure, using whole numbers, common fractions, and decimals. Requires ability to compute rate, ratio, and percent and to draw and interpret bar graphs. Reasoning Ability: Needs ability to apply common sense understanding to carry out instructions furnished in written, oral, or diagram form. Ability to investigate all steps and processes pertaining to product issues by analyzing applicable engineering design, specification and conformance requirements. Physical Demands The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is regularly required to stand; walk; use hands to finger, handle, or feel and talk or hear. The employee is frequently required to sit; reach with hands and arms and stoop, kneel, crouch, or crawl. The employee is occasionally required to climb or balance. The employee must regularly lift and/or move up to 10 pounds, frequently lift and/or move up to 25 pounds and occasionally lift and/or move up to 50 pounds. Specific vision abilities required by this job include close vision, distance vision, color vision, peripheral vision, depth perception, and the ability to adjust focus. While performing the duties of this job, the employee is regularly exposed to work near moving mechanical parts. The employee is frequently exposed to vibration. The employee is occasionally exposed to fumes or airborne particles. The noise level in the work environment is usually moderate. The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. Benefits We offer Medical, Dental, Vision, Life Insurance and a 401(k) plan with Employer’s match, safety incentives and an employee referral bonus program. We also provide paid holidays, vacation and sick days. Equal Opportunity Employer We are proud to be an equal opportunity employer to all, regardless of age, ancestry, color, disability (mental and physical), exercising the right to family care and medical leave, gender, gender expression, gender identity, genetic information, marital status, medical condition, military or veteran status, national origin, political affiliation, race, religious creed, sex (includes pregnancy, childbirth, breastfeeding and related medical conditions), and sexual orientation. #J-18808-Ljbffr