Maintenance Technician II - 2nd Shift

Maintenance TechnicianMaintain and repair mechanical and electrical systems within a manufacturing environment; execute capital projects (installation, dismantling of equipment) and other various maintenance tasks throughout the facility with key knowledge of the equipment and minimum supervision. Expected hours of work 40 hours a week with a varied shift schedule 8-10 hours shifts with occasional overtime and weekend hours. No travel required.Duties and Responsibilities:Reassemble machines after the completion of repair or maintenance work.Start machines and observe mechanical operation to determine efficiency and to detect problems.Inspect or test damaged machine parts and mark defective areas or advise supervisors of repair.Lubricate or apply adhesives or other materials to machines, machine parts, or other equipment according to specific procedures.Install, replace, or change machine parts and attachments according to production specifications.Dismantle machines and remove parts for repair using hand tools, chain falls, jacks, cranes, or hoists.Record production, repair, and machine maintenance information within MaintainX.Proper work order documentation and asset state updates in MaintainX.Maintain PM completion rate per MaintainX guidelines.Read work orders and specifications to determine machines and equipment requiring repair or maintenance.Set up and operate machines and adjust controls to regulate operations.Transport machine parts, tools, equipment, and other material between work areas and storage, using cranes, hoists, or dollies.Collect and discard worn machine parts and other refuse to maintain machinery and work areas.Clean machines and machine parts, using cleaning solvents, cloths, air guns, hoses, vacuums, or other equipment.Performing ongoing preventative maintenance on facility equipment.Repair or replace control devices such as switches, photo eyes, proximity sensors, push buttons, contactors, motor starters, etc. as needed.Comply and participate in regulatory, Carlisle, and departmental policies, procedures, and standards (PSM, safety protocols, COS)Articulate to vendors/engineer's machine issue to resolve technical issues.Assist with basic electronics/Programmable Logic Controls troubleshooting.Other duties as assigned.Required Knowledge/Skills/Abilities:Knowledge of measuring gauges such as tape measuresKnowledge and use of calipers, micrometers and digital multimeters (required)Knowledge of various hand and power toolsCertified to operate a forklift.Working knowledge of troubleshooting electrical, pneumatic, and hydraulics.Ability to comprehend complex technical topics and specialized information.Effective communication and problem-solving skillsUnderstanding of basic math, reading, and writing skillsAbility to work under pressure to complete assigned tasks under stressful situations.Ability to use hand & portable tools, gas and arc welder, forklift, pickup truck, testing equipment, tape measure, computer (shop floor and ERP).Ability to obtain rigging training and certification (as needed).Ability to obtain welding certification (as needed).Education and Experience:Required:Education – High School diploma or GED required.Two to Five (2- 5) years related maintenance experience; relevant Technical degree or certification.Must complete NFPA 70E training within 180 days of assignment.Previous experience in the following maintenance areas preferred: electrical, plumbing, carpentry, and welding.Mechanical background with rotating equipment. Hydraulic and pneumatic.Electrical troubleshooting (motors, sensors, relays, basic PLC I/O)Working Conditions:Fast paced manufacturing environment where workers are exposed to both ambient/outside temperatures and dust; working with mechanical parts and pinch points; exposure to increased noise levels.Exposure to hazardous mechanical, electrical and chemical substances/equipment.Confined workspaces.Physical Requirements:OCCASIONALLY - FREQUENTLY - CONTINUOUSLY(0-30%) - (31-60%) - (61-100%)LIFTING OR CARRYING1-10 LBS - X11-20 LBS - X21-40 LBS - X41-50 LBS51 OR MORE LBSPUSHING OR PULLING:1-40 LBS - X41-50 LBS - X51 OR MORE LBS - XBENDING OR STOOPING - XREACHING ABOVE SHOULDER LEVEL - XDRIVING AUTOMATIC EQUIP. VEHICLES - XOPERATE MACHINERY OR POWER TOOLS - XCLIMBING (LADDERS, STAIRS, ETC.) - XWALKING - XSTANDING - XSITTING - XWORKING IN EXTREME TEMPERATURES - XREPETATIVE MOTION INCLUDING BUT NOT LIMITED TO: WRISTS, HANDS AND/OR FINGERS) - XVISION - XHEARING - XDEXTERITY - XHAND EYE COORDINATION - XPersonal Protective Equipment (PPE) Used:Eye and hearing protection is required at all times on the production floor.Safety toe shoes (steel/composite).Flame Resistant rated Maintenance uniform provided.Other PPE as defined by management within assigned department.