Lead Coating Technician

Rotating Shift: One week of 7am -3pm: Mon -Fri, then a week of 3pm – 11pm: Mon - Fri, and rotate that schedule every other week.

Primary Duties & Responsibilities

Operation of thin film coating and test equipment including

• Retrieve proper designs according to set schedule and programs into coating system operations controller
• Operate coating equipment according to set parameter and establishing procedures
• Determine evaporation layer end points to high level of accuracy
• By observation and deduction, extract the maximum amount of data from each coating run and document accordingly
• Monitor two high volume coating chambers at one time, while supporting peers in their operations
• Communicate daily activities during quality meetings
• Operate characterization/test equipment and interpret results

• Maintain and adjust schedule to meet production demands and requirement

Coating Chamber Setup

• Evaluate design requirements and prepare evaporation materials accordingly
• Evaluate evaporation components to assure proper operation requirements
• Change out all worn/dirty components and replace with cleaned or new ones
• Observe and extract the maximum amount of data from each calibration/production run. Evaluate data from calibration/production runs and reports to engineering
• Use calibration equipment to assure proper setup and quality control
• Double check design and run requirements before loading run
• Document log information required for design operations
• Accept responsibility for the quality of the thin film coating process and equipment assigned. Accountable for operations directly involved

• Understand quality requirements for each coating run being performed

  Related Job Tasks

• Support cleaning area in loading of optical components
• Oversee setup and operation of process equipment
• Maintain inventory controls
• Perform minor maintenance with minimal support
• Take traces between coating runs to verify performance
• Understand nonstandard system operations
• Audit technicians for proper procedures and process consistency
• Train new technicians according to training program and audit regularly.
• Provide engineering support with timely, accurate information
• Lead daily quality meetings
• Assist in employee performance evaluations

Education & Experience

• High school graduate with good math or science skills
• 8 years coating or manufacturing experience and/or advanced education preferred
• Bachelor or Technical degree preferred

Skills

• Able to work in a demanding, fast-paced production environment
• Able to multi-task and prioritize
• Forward thinker
• Strong attention to detail and quality
• Team-oriented; works well with others in the group
• Excellent interpersonal and communication skills
• Must be able to effectively listen and assimilate, present organized trains of thought, assure a timely information exchange with others as required
• Ability to train others

Working Conditions

• Must be able to work with acids, radioactive materials and other toxic chemicals

• Make-up and perfumes discouraged while working in clean room to prevent contamination

Physical Requirements

• Long periods of standing and/or walking (3+ hours at a time)

• Must be able to wear a full-face respirator. Must be clean shaven

• Must be able to lift, push, pull up to 50 lbs.

• Bending and stooping required

• May need to utilize step stool or elevated working platform to adjust within coating chamber and to disassemble/reassemble

Safety Requirements

All employees are required to follow the site EHS procedures and Coherent Corp. Corporate EHS standards.

This position is subject to a pre-employment physical evaluation associated with wearing a respirator.

This position must under-go annual physical evaluations associated with respirator use.

Quality and Environmental Responsibilities

Depending on location, this position may be responsible for the execution and maintenance of the ISO 9000, 9001, 14001 and/or other applicable standards that may apply to the relevant roles and responsibilities within the Quality Management System and Environmental Management System.

Culture Commitment

Ensure adherence to company’s values (ICARE) in all aspects of your position at Coherent Corp.:

I ntegrity – Create an Environment of Trust

C ollaboration – Innovate Through the Sharing of Ideas

A ccountability – Own the Process and the Outcome

R espect – Recognize the Value in Everyone

E nthusiasm – Find a Sense of Purpose in Work

Coherent Corp. is an equal opportunity/affirmative action employer. All qualified applicants will receive consideration for employment without regard to sex, gender identity, sexual orientation, race, color, religion, national origin, disability, protected Veteran status, age, or any other characteristic protected by law.

If you need assistance or an accommodation due to a disability, you may contact us at View email address on aiapply.co .

#IND

Coherent is a global leader in lasers, engineered materials and networking components. We are a vertically integrated manufacturing company that develops innovative products for diversified applications in the industrial, optical communications, military, life sciences, semiconductor equipment, and consumer markets. Coherent provides a comprehensive career development platform within an environment that challenges employees to perform at their best, while rewarding excellence and hard-work through a competitive compensation program. It's an exciting opportunity to work for a company that offers stability, longevity and growth. Come Join Us!


Note to recruiters and employment agencies: We will not pay for unsolicited resumes from recruiters and employment agencies unless we have a signed agreement and have required assistance, in writing, for a specific opening.